Access the full text.
Sign up today, get DeepDyve free for 14 days.
P. Coussot, Q. Nguyen, H. Huynh, D. Bonn (2002)
Avalanche behavior in yield stress fluids.Physical review letters, 88 17
V. Fernàndez-Altable, I. Casanova (2006)
Influence of Mixing Sequence and Superplasticiser Dosage on the Rheological Response of Cement Pastes at Different TemperaturesCement and Concrete Research, 36
F. Rosquoet, A. Alexis, A. Khelidj, A. Phelipot (2003)
Experimental study of cement grout: Rheological behavior and sedimentationCement and Concrete Research, 33
M. Eriksson, M. Friedrich, C. Vorschulze (2004)
Variations in the rheology and penetrability of cement-based grouts—an experimental studyCement and Concrete Research, 34
R. Lapasin, A. Papo, S. Rajgelj (1983)
Flow behavior of fresh cement pastes. A comparison of different rheological instruments and techniquesCement and Concrete Research, 13
A. Bras, F. Henriques (2011)
Natural hydraulic lime based grouts – The selection of grout injection parameters for masonry consolidationConstruction and Building Materials, 26
(2009)
Introductions to rheology of fresh concrete, course compendium
N. Roussel (2005)
Steady and transient flow behaviour of fresh cement pastesCement and Concrete Research, 35
D. Cheng, F. Evans (1965)
Phenomenological characterization of the rheological behaviour of inelastic reversible thixotropic and antithixotropic fluidsBritish Journal of Applied Physics, 16
H. Barnes (1997)
Thixotropy—a reviewJournal of Non-newtonian Fluid Mechanics, 70
D. Piotrowski, C. Cierniewski (1982)
[Introduction to rheology].Acta haematologica Polonica, 13 3-4
P. Banfill, D. Saunders (1981)
On the viscometric examination of cement pastesCement and Concrete Research, 11
(2005)
Requirements for the choice of mortar and grouts for consolidation of three-leaf stone masonry walls. Paper presented at the Workshop Repair Mortars for historic masonry
(2000)
Characterization and modelling of the rheology of cement paste. With applications toward selfflowing materials
N. Roussel, F. Cussigh (2008)
Distinct-layer casting of SCC: The mechanical consequences of thixotropyCement and Concrete Research, 38
(2001)
Guide to rheological nomenclature for liquid-based particle systems. National Institute of Standards and Technology
A. Yahia, K. Khayat (2001)
Analytical models for estimating yield stress of high-performance pseudoplastic groutCement and Concrete Research, 31
A. Bras, F. Henriques (2009)
The influence of the mixing procedures on the optimization of fresh grout propertiesMaterials and Structures, 42
M. Sonebi (2006)
Rheological properties of grouts with viscosity modifying agents as diutan gum and welan gum incorporating pulverised fly ashCement and Concrete Research, 36
J. Wallevik (2009)
Rheological properties of cement paste: Thixotropic behavior and structural breakdownCement and Concrete Research, 39
G. Ovarlez, N. Roussel (2005)
A Physical Model for the Prediction of Lateral Stress Exerted by Self-Compacting Concrete on FormworkMaterials and Structures, 39
N. Roussel, G. Ovarlez, S. Garrault, C. Brumaud (2012)
The origins of thixotropy of fresh cement pastesCement and Concrete Research, 42
N. Roussel (2006)
A thixotropy model for fresh fluid concretes: Theory, validation and applicationsCement and Concrete Research, 36
Y. Otsubo, Seiichi Miyai, K. Umeya (1980)
Time-dependent flow of cement pastesCement and Concrete Research, 10
P. Billberg (2006)
Form pressure generated by self-compacting concrete : influence of thixotropy and structural behaviour at rest
A. Bras, F. Henriques, M. Cidade (2010)
Effect of environmental temperature and fly ash addition in hydraulic lime grout behaviourConstruction and Building Materials, 24
This paper deals with the coupled effect of temperature and fly ash (FA) addition on rheological behaviour of natural hydraulic lime (NHL5) based grouts, currently used in masonry consolidation. The use of a grout injection technique for masonry consolidation may lead to an increase of hydrostatic pressure and lead to structural damage. This means that the thixotropic effects become self-evident in grout design. It was shown that there is a relation between the structuration rate of each grout and the pressure that occurs inside masonry during its consolidation. According to the results, it seems also that there is a grout threshold temperature ( T limit ) that separates a domain where the grout build-up structure area is almost constant, from another where flocculation area starts to increase significantly. We believe that in the first region the thixotropic effects are almost isolated from the irreversible effects (due to hydration). For the NHL5 based grout T limit =20 °C and for the grout with NHL5+15 % of FA T limit =15 °C. Grouts’ characterization based on maximum resisting time, structuration rate and on the analysis of the hydraulic lime grout behaviour tested at different shear rates was performed using a shear thinning model and assuming that the structure is shear- and time-dependent. The goal is to use this methodology during mix proportioning and design for masonry injection purpose. The tested grout compositions were optimized compositions obtained in previous research using the design of experiments method.
Mechanics of Time-Dependent Materials – Springer Journals
Published: May 1, 2013
Read and print from thousands of top scholarly journals.
Already have an account? Log in
Bookmark this article. You can see your Bookmarks on your DeepDyve Library.
To save an article, log in first, or sign up for a DeepDyve account if you don’t already have one.
Copy and paste the desired citation format or use the link below to download a file formatted for EndNote
Access the full text.
Sign up today, get DeepDyve free for 14 days.
All DeepDyve websites use cookies to improve your online experience. They were placed on your computer when you launched this website. You can change your cookie settings through your browser.