Access the full text.
Sign up today, get DeepDyve free for 14 days.
C. McCall (1985)
Thermal Properties of SandwichPanelsConcrete international, 7
E. Losch, Patrick Hynes, Ray Andrews, Ryan Browning, Paul Cardone, R. Devalapura, R. Donahey, S. Freedman, H. Gleich, G. Goettsche, Paul Kourajian, J. Krohn, Chris Leaton, Zhengsheng Li, R. Long, D. Meinheit, Michael Milkovitz, B. Miller, F. Nadeau, Brad Nesset, S. Pessiki, David Peterson, S. Peterson, Rene Quiroga, S. Reay, W. Richardson, Kim Seeber, Venkatesh Seshappa, D. Smith, Bryan Trimbath, Karl Truderung, Mike Wagner, Charles Wynings, Li Yan (2011)
State of the Art of Precast/Prestressed Concrete Sandwich Wall Panels, 2nd ed.PCI Journal
B. Frankl, G. Lucier, T. Hassan, S. Rizkalla (2011)
Behavior of precast, prestressed concrete sandwich wall panels reinforced with CFRP shear gridPci Journal, 56
(2010)
Experimental and theoretical studies on the mechanical properties of steel-FRP composite bars properties of steel-FRP composite bars
Tae Oh, Seok-Joon Jang, Kangmin Lee, H. Yun (2013)
Insulation Type Effect on the Direct Shear Behavior of Concrete Sandwich Panel (CSP) with Non-Shear ConnectorsAdvanced Materials Research, 663
T. Hassan, S. Rizkalla (2010)
Analysis and design guidelines of precast prestressed concrete, composite Ioad-bearing sandwich wall panels reinforced with CFRP, gridPci Journal, 55
Junhee Kim, Young-chan You (2015)
Composite Behavior of a Novel Insulated Concrete Sandwich Wall Panel Reinforced with GFRP Shear Grids: Effects of Insulation TypesMaterials, 8
D. Tomlinson, A. Fam (2014)
Experimental Investigation of Precast Concrete Insulated Sandwich Panels with Glass Fiber-Reinforced Polymer Shear ConnectorsAci Structural Journal, 111
Clay Naito, J. Hoemann, B. Bewick, M. Hammons (2009)
Evaluation of Shear Tie Connectors for Use in Insulated Concrete Sandwich Panels
A. Einea, David Salmon, M. Tadros, Todd Culp (1994)
A new structurally and thermally efficient precast sandwich panel systemPci Journal, 39
In-Hyu Choi, Junhee Kim, Ho-Ryong Kim (2015)
Composite Behavior of Insulated Concrete Sandwich Wall Panels Subjected to Wind Pressure and SuctionMaterials, 8
Gregory Woltman, D. Tomlinson, A. Fam (2011)
A Comparative Study of Various FRP Shear Connectors for Sandwich Concrete Walls
Byoung-Jun Lee, S. Pessiki (2007)
Design and analysis of precast, prestressed concrete, three-wythe sandwich wall panelsPci Journal, 52
A. Benayoune, A. Samad, D. Trikha, Abang Ali, S.H.M. Ellinna (2008)
Flexural behaviour of pre-cast concrete sandwich composite panel – Experimental and theoretical investigationsConstruction and Building Materials, 22
D. Tomlinson, A. Fam (2015)
of precast concrete sandwich wall panels with basalt FRP and steel reinforcement
A new shear connector is proposed in this article. The shear connector is made of steel–glass fiber–reinforced polymer material. Twelve full-scale precast insulated concrete sandwich panels were tested under flexure to analyze their flexural behavior subjected to pressure. The test program was composed of eight sandwich panels with steel–glass fiber–reinforced polymer connectors and four panels for comparison that were panels using stainless steel truss connectors, pure glass fiber–reinforced polymer pin connectors, and no connectors, respectively. Their load–deflection relationships, load–slip relationships, concrete strain profiles along the wythes cross section, as well as the strains in the steel–glass fiber–reinforced polymer W-shaped connectors were investigated in this article. The panels exhibited a composite action in terms of strength exceeding 85% with steel–glass fiber–reinforced polymer connectors and 40 mm insulation thickness. In addition, the other panels with more than 40 mm insulation layer and different diameter connectors only exhibited 26%–62% composite action. When evaluating the degree of the composite action in terms of stiffness, all sandwich panel values ranged from 6% to 26%. But the compared specimens with pure glass fiber–reinforced polymer connector and smaller diameter steel truss connector had lower level composite action less than 10%. Reasonable design of steel–glass fiber–reinforced polymer W-shaped connectors may provide high composite action for panels and prevent the strength from dropping rapidly due to the steel inner core in the connectors.
Advances in Structural Engineering – SAGE
Published: Oct 1, 2017
Read and print from thousands of top scholarly journals.
Already have an account? Log in
Bookmark this article. You can see your Bookmarks on your DeepDyve Library.
To save an article, log in first, or sign up for a DeepDyve account if you don’t already have one.
Copy and paste the desired citation format or use the link below to download a file formatted for EndNote
Access the full text.
Sign up today, get DeepDyve free for 14 days.
All DeepDyve websites use cookies to improve your online experience. They were placed on your computer when you launched this website. You can change your cookie settings through your browser.