Access the full text.
Sign up today, get DeepDyve free for 14 days.
Loading next page...
/lp/sage/behaviour-and-design-of-stainless-steel-bolted-connections-BN1P0G0EVs
References (20)
-
B. Burgan, N. Baddoo, L. Gardner, J. Way, B. Johansson, A. Olssen, E. Selén, R. Viherma, J. Kouhi, A. Talja, V. Lihavainen, E. Niemi, I. Ryan, B. Zhao, H. Stangenberg, M. Barteri, S. Budano, S. Riscifuli (2001)
Development of the use of stainless steel in constructionEuropace
-
(2005)
Pawtucket, USA -
S. Errera, D. Popowich, G. Winter (1974)
BOLTED AND WELDED STAINLESS STEEL CONNECTIONSJournal of the Structural Division, 100
-
(1969)
Tension Capacity of Bolted Connections in Light Gage Cold-Formed -
G. Winter (1956)
Tests on Bolted Connections in Light Gage SteelJournal of the Structural Division, 82
-
P. Merwe (1987)
Development of design criteria for ferritic stainless steel cold-formed structural members and connections -
N. Null (2002)
Specification for the Design of Cold-Formed Stainless Steel Structural Members -
L. Gardner (2005)
The use of stainless steel in structuresProgress in Structural Engineering and Materials, 7
-
E. Mirambell, E. Real (2000)
On the calculation of deflections in structural stainless steel beams: an experimental and numerical investigationJournal of Constructional Steel Research, 54
-
K. Chung, K. Ip (2000)
Finite element modeling of bolted connections between cold-formed steel strips and hot rolled steel plates under static shear loadingEngineering Structures, 22
-
M. Theofanous, L. Gardner (2010)
Experimental and numerical studies of lean duplex stainless steel beamsJournal of Constructional Steel Research, 66
-
TaeSoo Kim, H. Kuwamura, T. Cho (2008)
A parametric study on ultimate strength of single shear bolted connections with curlingThin-walled Structures, 46
-
E. Salih, L. Gardner, D. Nethercot (2010)
Numerical investigation of net section failure in stainless steel bolted connectionsJournal of Constructional Steel Research, 66
-
A. Bouchaïr, Julien Averseng, Anis Abidelah (2008)
Analysis of the behaviour of stainless steel bolted connectionsJournal of Constructional Steel Research, 64
-
M. Theofanous, L. Gardner (2009)
Testing and numerical modelling of lean duplex stainless steel hollow section columnsEngineering Structures, 31
-
William Perry (1981)
The bearing strength of bolted connections -
C. Rogers, G. Hancock (1999)
Bolted connection design for sheet steels less than 1.0 mm thickJournal of Constructional Steel Research, 51
-
S. Ju, C. Fan, G. Wu (2004)
Three-dimensional finite elements of steel bolted connectionsEngineering Structures, 26
-
K. Rasmussen (2003)
Full-range stress–strain curves for stainless steelalloys -
R. Puthli, O. Fleischer (2001)
Investigations on bolted connections for high strength steel membersJournal of Constructional Steel Research, 57
- Publisher
- SAGE
- Copyright
- © 2011 SAGE Publications
- ISSN
- 1369-4332
- eISSN
- 2048-4011
- DOI
- 10.1260/1369-4332.14.4.647
- Publisher site
- See Article on Publisher Site
Abstract
Using previously developed and validated finite element (FE) models, an investigation into the behaviour of stainless steel bolted connections has been carried out. Both net section rupture and bearing failure were studied. The main parameters affecting net section rupture were found to be edge distance e2 and bolt configuration. It was shown that the ductility of stainless steel is sufficient to ensure a failure at the full fracture load (net area multiplied by ultimate tensile strength) for both thick and thin material and hence no reduction factor is required in the design equation. This was confirmed by reliability analysis and a suitable partial safety factor has been derived. The investigation into bearing behaviour showed that the deformation response of stainless steel connections is different from that of carbon steel connections, with stainless steel exhibiting pronounced strain hardening. The locations of fracture initiation obtained from the numerical models match those observed during experimental studies of carbon steel and stainless steel connections. The results of the parametric study were utilised as the basis for the development of design provisions for bearing failure in stainless steel bolted connections, covering both cases in which deformation controls and those for which ultimate strength is the only criterion.
Journal
Advances in Structural Engineering – SAGE
Published: Aug 1, 2011