Membranes for the Capture and Screening of Waterborne Plutonium Based on a Novel Pu-Extractive Copolymer Additive

James C. Foster; Timothy A. DeVol; Scott M. Husson

doi:10.3390/membranes12010003

Membranes for the Capture and Screening of Waterborne Plutonium Based on a Novel Pu-Extractive Copolymer Additive

Foster, James C.;DeVol, Timothy A.;Husson, Scott M. 2021-12-21 00:00:00 membranes Article Membranes for the Capture and Screening of Waterborne Plutonium Based on a Novel Pu-Extractive Copolymer Additive 1 , 2 2 , 3 1 , James C. Foster , Timothy A. DeVol and Scott M. Husson * Department of Chemical and Biomolecular Engineering, Clemson University, 127 Earle Hall, Clemson, SC 29634, USA; jcf@clemson.edu Nuclear Environmental Engineering Sciences, Radioactive Waste Management Center, Clemson University, Clemson, SC 29625, USA; devol@clemson.edu Department of Environmental Engineering and Earth Sciences, Clemson University, 342 Computer Court, Anderson, SC 29625, USA * Correspondence: shusson@clemson.edu Abstract: This contribution describes the fabrication of plutonium-adsorptive membranes by non- solvent induced phase separation. The dope solution comprised poly(vinylidene ﬂuoride) (PVDF) and a Pu-extractive copolymer additive of PVDF-g-poly(ethylene glycol methacrylate phosphate) (EGMP) in dimethylformamide (DMF). The effects of casting conditions on membrane permeability were determined for PVDF membranes prepared with 10 wt% PVDF-g-EGMP. Direct-ﬂow ﬁltration and alpha spectrometry showed that membranes containing the graft copolymer could recover Pu up to 59.9 3.0% from deionized water and 19.3 3.5% from synthetic seawater after ﬁltering 10 mL of 0.5 Bq/mL Pu. SEM-EDS analysis indicated that the graft copolymer was distributed evenly throughout the entire depth of the copolymer membranes, likely attributing to the tailing observed in the alpha spectra for Pu. Despite the reduction in resolution, the membranes exhibited high Pu uptake at the conditions tested, and new membrane designs that promote copolymer surface Citation: Foster, J.C.; DeVol, T.A.; migration are expected to improve alpha spectrometry peak energy resolutions. Findings from this Husson, S.M. Membranes for the study also can be used to guide the development of extractive membranes for chromatographic Capture and Screening of Waterborne separation of actinides from contaminated groundwater sources. Plutonium Based on a Novel Pu-Extractive Copolymer Additive. Keywords: extractive membranes; nuclear forensics; plutonium isotopic screening; alpha spectrometry; Membranes 2022, 12, 3. https:// non-solvent induced phase separation doi.org/10.3390/membranes12010003 Academic Editors: Mohd Haﬁz Dzarfan Othman, Juhana Jaafar and Mukhlis A. Rahman 1. Introduction The development of rapid analytical tools for the detection of waterborne special Received: 26 November 2021 Accepted: 17 December 2021 nuclear materials is a critical focus of nuclear forensics efforts. Trace levels of Pu exist Published: 21 December 2021 in the environment as a result of human nuclear activity, and while weapons testing accounts for the largest source of Pu, accidental releases from nuclear power and nuclear Publisher’s Note: MDPI stays neutral processing facilities also have led to increased levels of Pu near those sites. The abundances with regard to jurisdictional claims in of Pu isotopes in each source act as a unique signature or “ﬁngerprint”, and the isotopic published maps and institutional afﬁl- ratios can indicate where the Pu was produced and its ﬁnal intended use. For example, iations. approximately 6.1 PBq (~20 kg) of Pu was released from the disaster at Chernobyl Nuclear 238 239 Power Plant in 1986, and it is estimated that the Pu consisted of 0.3% Pu, 66.9% Pu, 240 241 25.3% Pu, and 7.5% Pu by mass [1]. Unique Pu signatures also can be traced to a 240 239 Copyright: © 2021 by the authors. particular production facility, and the Pu/ Pu ratio can elucidate the intended use Licensee MDPI, Basel, Switzerland. for the produced Pu. The assembly of a ﬁssion-type nuclear weapon requires a reactor This article is an open access article design and operation to promote the growth of Pu while limiting the production of distributed under the terms and Pu. Generally, uranium target materials spend less time in the reactor and multiple conditions of the Creative Commons batch cycles followed by chemical reprocessing are needed to produce sufﬁcient Pu for Attribution (CC BY) license (https:// 239 a weapon [2]. Illicit proliferation of Pu is likely to leave trace levels of Pu in nearby creativecommons.org/licenses/by/ waters. Due to the low solubility and complex redox chemistry of waterborne Pu, direct 4.0/). Membranes 2022, 12, 3. https://doi.org/10.3390/membranes12010003 https://www.mdpi.com/journal/membranes Membranes 2022, 12, 3 2 of 15 measurements require a multi-step approach to perform isotopic analysis. Pu isolation and pre-concentration usually cannot be performed in the ﬁeld as it requires highly acidiﬁed or caustic solutions to separate Pu from a solution matrix. Therefore, an on-site analytical method that can concentrate Pu quickly to detectable limits while simultaneously screening for its isotopic abundance would be a valuable nuclear forensics tool. Instruments such as inductively coupled mass spectrometry (ICP-MS) and thermal ionization mass spectrometry (TIMS) are capable of screening for Pu isotopes at concen- trations as low as a few parts per billion; however, the size of these instruments and their respective equipment do not lend well for transport. Comparatively, an alpha spectrometer has the capability to be made into a ﬁeldable detection system for Pu and other alpha- emitters. For high resolution spectra, samples need to be dispersed thinly over a smooth surface to reduce alpha particle energy attenuation prior to reaching the detector. For this reason, electrodeposition remains the standard method for alpha spectrometry source preparation, as it can achieve peak resolutions (reported as full-width at half maximum, FWHM) from about 15 to 55 keV for Pu isotopes [3]. Preparing an electrodeposited Pu source from a contaminated water can be challenging and time-consuming as the Pu has to be isolated through separation techniques such as coprecipitation, liquid–liquid extraction or ion-exchange chromatography. Detection limits for alpha spectrometry are on the scale of 10 Bq, meaning that high volumes of a trace-level Pu solution would need to be processed to generate the activity needed for detection [4]. To reduce the time to prepare an alpha spectrometry source, we and others have turned to developing Pu extractive membranes that can concentrate Pu to detectable limits and serve directly as the sample source. Membranes are functionalized for Pu capture either by casting a polymer-ligand ﬁlm onto the membrane surface, or by utilizing a reactive surface from which a ligand layer can be grafted [5–10]. By keeping the functional layer relatively thin, high spectral resolutions can be achieved that rival electrodeposited sources. Careful consideration needs to be taken regarding the physical properties of the membrane support as the pore size and density affect overall throughput of a Pu-contaminated water source [10]. For nuclear forensics applications, the extractive membranes need to balance permeability, Pu uptake, and alpha spectrometry peak resolutions. Pu-binding ligands are chosen based on the approach used to incorporate them in or onto a membrane, and for their ability to complex with Pu depending on its oxidation state and solution conditions. Of relevance to the current study, membranes functionalized with ethylene glycol methacrylate phosphate (EGMP) have been shown to be capable of extracting Pu over a broad pH range. The phosphate group (with pK values of 1.6 and 6.6) can interact with Pu through ion-exchange or by chemical coordination. The dual functionality of EGMP was demonstrated in a study by Vasudevan et al., where polypropy- lene membranes grafted with EGMP recovered greater than 90% of Pu(IV) from solutions ranging from 0 to 4 M nitric acid [11]. Other studies have shown that membranes containing EGMP can serve directly as an alpha spectrometry sample source for actinides. Duval et al. developed a method to graft EGMP from polyethersulfone membranes for the isotopic screening of waterborne uranium. After ﬁltering solutions spiked with U, the modiﬁed membranes achieved U peak resolutions ranging from 17 to 33 keV FWHM [12]. Further- more, the peak resolutions achieved by the membranes were sharp enough to distinguish 238 234 U (4.198 MeV) from U (4.775 MeV) after ﬁltering a spiked groundwater source at pH 6. In our previous study [13], extractive thin-ﬁlm composite (e-TFC) membranes were developed for the rapid capture and isotopic screening of Pu in water. The e-TFC mem- branes were made by spin coating a thin copolymer ﬁlm consisting of 5% (w/w) EGMP and 4-methylstyrene (a.k.a. vinyltoluene, VT) onto a poly(vinylidene ﬂuoride) (PVDF) ultraﬁltration membrane. Direct ﬂow ﬁltration studies indicated that the e-TFC mem- 242 242 branes recovered up to 10.2 4.2% of Pu after ﬁltering 10 mL of a 4.53 Bq/mL Pu solution at pH 6.8, and the 16 h alpha spectra exhibited average energy resolutions of 71.7 8.7 keV for the Pu peak. While spin coating provided a simple and effective way to cast a Pu-selective polymer onto a membrane, the addition of the poly(EGMP-co-VT) Membranes 2022, 12, 3 3 of 15 layer greatly reduced the overall permeability of the membrane. At trace-level Pu con- 12 10 centrations (10 to 10 M), the reduced permeability of the e-TFC membranes poses concern as the membranes need to be able to process large volumes of solution rapidly to reach alpha spectrometry detection limits. The aim of this study was to develop a Pu-extractive membrane with high permeability for rapid concentration and alpha spectroscopy analysis of trace-level Pu from water. For high alpha spectra energy resolution, the extractive functional layer should be thin and able to sequester Pu onto the surface of the membrane. The method for membrane fabrication was inspired by the approach used by Hester et al. [14] to develop fouling-resistant graft copolymer membranes. They demonstrated that hydrophilic poly(oxyethylene methacry- late) (POEM) and poly(methacrylic acid) (PMAA) could be grafted directly by atom transfer radical polymerization (ATRP) from the secondary ﬂuorinated sites in PVDF. This created amphiphilic copolymers consisting of a hydrophobic PVDF anchor with a hydrophilic POEM or PMAA comb shell. PVDF membranes were prepared by nonsolvent induced phase separation (NIPS) using dope solutions containing 5–10 wt% PVDF-g-POEM. It was observed that the amphiphilic nature of the copolymer would lead it to segregate to the membrane surface upon formation. In membranes containing 10 wt% PVDF-g-POEM, the surface migration greatly improved the wetting of the membrane and reduced protein adsorption over seven-fold compared to PVDF membranes. This study demonstrated a simple approach to casting functional membranes without the need for post-modiﬁcation steps. Here, we used ATRP to graft EGMP from PVDF. We theorized that the addition of this Pu-selective PVDF-g-EGMP copolymer in the dope solution during membrane formation by NIPS would yield a high permeability, Pu-extractive membrane. We theorized further that, given the hydrophilicity of EGMP, the graft copolymer would migrate to the surface of the membrane where it would concentrate Pu during ﬁltration and enable high spectral resolution when the membrane is screened in an alpha spectrometer. 2. Materials and Methods 2.1. Materials The following chemicals were purchased from MilliporeSigma (St. Louis, MO, USA): copper(I) chloride (CuCl, 97%); dimethylformamide (DMF, 99.8%); inhibitor remover (alu- minum oxide, activated); methanol (95%); n-methyl-2-pyrrolidone (NMP, 99.5%); phospho- ric acid 2-hydroxyethyl methacrylate ester (further denoted as ethylene glycol methacrylate phosphate, EGMP, 90%); PVDF (M ~250,000 g/mol); PVDF (M ~534,000 g/mol); w w 250K 534K and tris(2-pyridyl methyl) amine (TPMA, 98%). Chemicals purchased from Fisher Sci- entiﬁc (Waltham, MA, USA) were nitric acid (HNO , 65% w/w); petroleum ether (ACS reagent, 35–60 C boiling range); and sodium hydroxide (NaOH, 97%). Instant Ocean Synthetic Sea Salt was purchased from Carolina Biological Supply Company (Burlington, NC, USA). Nitrogen gas and dry air was from Airgas (Radnor, PA, USA). Type-1 deionized (DI) water was produced using a Millipore Milli-Q Reference water puriﬁcation system (Darmstadt, Germany). 242 242 2+ Pu solutions were prepared from a 147 Bq/mL Pu(VI) (PuO ) stock in 1 mM HNO provided by Dr. Brian Powell (Clemson University, Department of Environmental Engineering and Earth Sciences). Low-activity solutions were diluted from the stock with DI water, followed by conditioning with 0.1 and 1 M aliquots of HNO and NaOH to achieve circumneutral pH conditions immediately prior to use. Table S1 in Supplementary Materials reports mass fractions of the Pu isotopes in the stock solution. For the direct ﬂow ﬁltration study, Pu solutions were prepared by dilution in DI water and synthetic seawater from a NIST traceable Pu stock (Eckert & Ziegler, Valencia, CA, USA) with an activity of 2464 Bq/mL in 0.1 M HNO . The dilutions were conditioned with 0.1 and 1 M aliquots of HNO and NaOH to adjust the pH to circumneutral conditions. The solutions were set aside for 3 d to allow for equilibrium between Pu oxidation states. Synthetic seawater was prepared using Instant Ocean Synthetic Sea Salt to replicate typical seawater conditions. Table S2 in Supplementary Materials provides the composition of Membranes 2022, 12, 3 4 of 15 the solution. Pu oxidation states of the Pu dilutions were determined through a solvent extraction method outlined by Powell et al. [15]. 2.2. Synthesis of PVDF-g-EGMP Copolymer Prior to copolymer synthesis, monomethyl ether hydroquinone was removed from the EGMP by combining 1 g EGMP and 20 mg inhibitor remover and stirring for at least 1 h. A Cu-TPMA solution was prepared by dissolving 40 mg CuCl and 180 mg TPMA in 5 mL NMP under an inert N atmosphere in a glovebox (MBRAUN, Garching, Germany). An EGMP solution was prepared in a Schlenk ﬂask by dissolving 15 g EGMP in 20 mL NMP. In a separate Schlenk ﬂask, 5 g PVDF was dissolved in 30 mL NMP. Dissolved 250K air was removed from the EGMP and PVDF solutions through a freeze-pump-thaw 250K procedure. First, the ﬂasks were sealed and placed in a liquid nitrogen bath until the contents were frozen solid. A vacuum line was attached, and the ﬂasks were submerged in a 75 C water bath while under vacuum to thaw. This process was repeated for at least three cycles, or until visible air bubbles were no longer formed during the thawing step. The EGMP and PVDF solutions were left sealed under vacuum until further use. 250K ATRP grafting of EGMP from PVDF was performed in the N glove box where the Cu- TPMA solution was stored. The prepared EGMP and PVDF solutions were combined 250K in a reaction vessel and heated to 90 C stirring by a magnetic stir bar at 300 RPM. Once the set temperature was reached, the Cu-TPMA solution was added to the reaction mixture, and the ATRP reaction proceeded for 24 h. Afterwards, the reaction vessel was removed from the glove box. PVDF-g-EGMP was precipitated from solution with a mixture of 50 mL methanol and 100 mL petroleum ether. To remove unreacted EGMP monomer, the precipitated PVDF-g-EGMP was dissolved again in NMP, followed by precipitation with the methanol/petroleum ether mixture. The copolymer was dried for at least 24 h in a fume hood at room temperature. Characterization of PVDF-g-EGMP was done by attenuated total reﬂectance Fourier-transform infrared spectroscopy (ATR-FTIR) on a PerkinElmer Spectrum II equipped with a diamond crystal. Spectra were generated from 32 scans at a resolution of 8 cm using PerkinElmer Spectrum 10 software. 2.3. Screening of PVDF-g-EGMP Copolymer for Pu Uptake Pu-uptake measurements were performed with PVDF-g-EGMP to quantify Pu uptake 242 242 from solutions at neutral pH conditions. A Pu(VI) solution was diluted from the Pu stock to produce a solution with a ﬁnal activity of 2.67 Bq/mL and pH 6.92. One hundred milligrams of the PVDF-g-EGMP copolymer was placed in a 1.5 mL vial with 1 mL of the Pu solution. The sample was stirred for 24 h on a Stuart SB2 rotator (Staffordshire, UK) set to 20 RPM. Afterwards, 0.5 mL of solution from each sample was removed and pipetted onto a 30 mm diameter steel planchette. Once planchettes were dry, they were placed 5 mm from the detector face in an alpha spectrometer and counted for 5 h. A control study was performed by repeating the study with PVDF in-lieu of the grafted copolymer, and Pu 534K sorption to the vials was accounted for by performing the experiment with empty vials. All sample trials were performed in triplicate measurements to determine average values and standard deviations for Pu uptake. 2.4. Casting PVDF Membranes with PVDF-g-EGMP Grafted copolymer membranes were cast from dope solutions using the formulations shown in Table 1, designed to produce membranes composed of approximately 10 wt% PVDF-g-EGMP. Dope solutions were prepared by dissolving PVDF and PVDF-g-EGMP 534K in DMF for 24 h under stirring, or until the polymer was fully dissolved. To study the effects of permeability on Pu uptake and alpha spectra peak resolution, glycerol was added to the dope solutions at 2 wt% to increase the porosity of the membranes. Membranes 2022, 12, 3 5 of 15 Table 1. Compositions of the dope solutions prepared for casting poly(vinylidene ﬂuoride) (PVDF) membrane composed of 10% PVDF-g-EGMP (ethylene glycol methacrylate phosphate) in dimethyl- formamide (DMF). Membrane Dope Solutions DMF PVDF PVDF-g-EGMP Glycerol 534K Membrane [g] [g] [g] [g] 10% PVDF-g-EGMP No glycerol 47.2 7.5 0.83 0 10% PVDF-g-EGMP 2 wt% glycerol 46.1 7.5 0.83 1.11 Membrane formation was achieved through NIPS. Prior to membrane casting, the polymer dope solutions were vacuum degassed at 75 kPa to remove any dissolved air from solution. The solutions were cast onto a clean glass plate and drawn using a doctor blade (Gardco, Pompano Beach, FL, USA) set to a height of 0.18 mm. Five seconds after drawing, the glass plate was immersed in a DI water bath for at least 2 min, resulting in the complete coagulation of the membrane onto the glass plate. Afterwards, the membranes were removed from the bath and stored in fresh DI water until further use. 2.5. Permeability Studies Grafted copolymer membranes were cut to 45 mm diameter coupons and placed in a Sterlitech HP4750 ﬂow cell (Kent, WA, USA). The cell was ﬁlled with DI water and sealed. Prior to measurements, the ﬂow cell was pressurized to 4.14 barg for 15 min to condition the membrane prior to taking measurements. Afterwards, the operating pressure was reduced to 0.69 barg. Flux measurements were taken at four setpoints as the pressure was increased from 1.38 to 3.45 barg. At each pressure setpoint, ﬁltrate mass and ﬂow time were recorded to determine water ﬂux and permeability. After the ﬁrst pressure cycle, cell pressure was reduced to 0.69 barg, and measurements were taken over a second pressure ramp to observe whether hysteresis occurred. For each membrane casting condition studied, average permeability values and uncertainty were calculated from ﬁve membrane samples. 2.6. SEM Analysis of Membrane Morphologies Scanning electron microscopy imaging with electron dispersive spectroscopy (SEM- EDS) was performed on the copolymer membranes to visualize morphology and locate where PVDF-g-EGMP copolymer resides within the membrane structure. Prior to measure- ments, membrane samples were washed sequentially for 1 h increments in water/ethanol solutions consisting of 25, 50, and 75 wt% ethanol. After drying from the 75 wt% ethanol solution, the samples were mounted to an aluminum holder with carbon tape. Samples were prepared so that the topside and cross-section morphologies could be analyzed. To analyze the membrane cross-section, samples were submerged in liquid nitrogen, freeze fractured, and mounted to the aluminum holder with the fractured edge exposed. Samples for topside surface imaging were coated with platinum for 40 min using an Anatech Hummer 6.5 sputter coater (Sparks, NV, USA). Micrographs were taken of the membrane surfaces using a Hitachi Regulus 8230 SEM (Tokyo, Japan) at an accelerating voltage of 2 kV. For the cross-sectional samples, platinum coating was not required; instead, the samples were measured on a Hitachi SU5000 SEM equipped with an Oxford Instru- ments X-Max 80 silicon drift detector for EDS (High Wycombe, UK). The samples were screened at an accelerating voltage of 10 kV, and chemical imaging of the cross-section was performed using AztectLive v3.3 software (Oxford Instruments, High Wycombe, UK). Pore size diameter measurements were averaged over twenty pores using ImageJ image analysis software, freely available online from the National Institutes of Health (Bethesda, MD, USA). Membranes 2022, 12, 3 6 of 15 2.7. Alpha Spectrometry Measurements Alpha spectrometry was performed using an Ortec 7401 alpha spectrometer (Oak Ridge, TN, USA) equipped with a 450 mm passivated ion silicon detector (PIPS). Peak energy calibration was performed with a 30 mm diameter Eckert & Ziegler electrodeposited source 234 238 239 241 containing known quantities of U, U, Pu, and Am. The calibration source was placed 5 mm from the PIPS detector and counted for 1 h. Absolute detector efﬁciency was determined for the 45 mm diameter membranes by spotting 5 Bq of the stock Pu solution onto the surface of a PVDF membrane. The droplets were carefully smeared across the membrane surface using a pipette tip. Once dry, the membrane was ﬁxed into a custom acrylic holder and placed 5 mm away from the PIPs detector to be counted for 1 h. 2.8. Direct Flow Filtration of Pu Solutions through PVDF-g-EGMP Membranes Membranes cast with 10 wt% PVDF-g-EGMP were cut into 45 mm diameter coupons and placed in a Amicon ultraﬁltration cell (EMD Millipore, Burlington, MA, USA). Two Pu solutions were prepared for the study: a spiked DI water solution with an activity of 0.48 0.01 Bq/mL and pH 6.61, and a synthetic seawater solution with an activity of 0.51 0.01 Bq/mL and pH 6.58. Filtration and alpha spectrometry procedures were the same for DI water and synthetic seawater trials. The Amicon ﬂow cell was ﬁlled with 10 mL of the prepared Pu solution. The cell was sealed and pressurized to 0.69 barg using a dry air cylinder to start ﬁltration. Once all of the Pu solution was ﬁltered, the cell was reﬁlled with 10 mL DI water and pressurized to 0.69 barg to perform a wash cycle to remove Pu from the membrane pores. The membrane was removed once the cell was completely empty of its contents and depressurized. Membrane samples were dried for at least 1 h before alpha spectrometry measurements. Alpha spectrometry was performed by mounting the membranes in a custom acrylic holder placed 5 mm from the detector face, followed by counting for 5 h. 3. Results 3.1. PVDF-g-EGMP Synthesis and Characterization FTIR analysis was performed on the PVDF-g-EGMP copolymer to determine if it exhibited characteristic peaks of EGMP. Figure 1 shows FTIR spectra for the graft copolymer, along with EGMP and PVDF precursors. Distinct peaks for the two precursors were observed in the graft copolymer, indicating successful grafting of EGMP from the PVDF macroinitiator. Characteristic absorbance peaks for EGMP were noted at 1720 and 980 cm assigned to C=O and P=O stretching, while peaks at 1400 and 880 cm correspond to vibrational bands observed in semi-crystalline PVDF [16,17]. 3.2. Permeability Measurements of PVDF-g-EGMP Membranes Direct-ﬂow water permeability measurements were carried out for the 10 wt% PVDF- g-EGMP copolymer membranes. Casting conditions were varied to determine the effects on membrane permeabilities. The copolymer membranes were cast (1) with or without vacuum degassing of the polymer solution prior to casting; (2) with or without the addition of 2 wt% glycerol; and (3) by waiting a short (5 s) or long (30 s) period between casting and submerging into the coagulation bath. Casting conditions are summarized in Table S3, and the resulting water ﬂux data for each membrane are given in Figure S1. The linear relationship between water ﬂux and transmembrane pressure is given by Equation (1), where J represents water ﬂux (in L/m /h, further denoted as LMH), A is the permeability coefﬁcient (LMH/bar), and DP is the transmembrane pressure (bar). J = ADP (1) Membranes 2022, 12, 3 7 of 15 Figure 1. Attenuated-total reﬂectance Fourier-transform infraredspectra of the PVDF-g-EGMP copoly- mer, EGMP monomer, and PVDF used in atom transfer radical polymerization (ATRP)grafting. Figure 2 shows the average permeability coefﬁcients for each membrane, along with the conditions used to prepare the membranes. The permeability of the membranes in- creased with the incorporation of glycerol and when the copolymer dope solution was not degassed by vacuum prior to casting. The increase in permeability for non-degassed samples was likely due to dissolved air present in the membrane casting solutions, poten- tially leading to the formation of voids during the coagulation process. Degassing is often a critical step in phase inversion processes as it prevents the formation of microbubbles as the polymer begins to solidify [18]. To determine whether the short or long wait times affected the overall permeability of the copolymer membranes, comparisons were made between treatments using a two-tailed separate-variance (Welch’s) t-test. At an level of 0.05, it was observed for the two wait times that differences in permeability were signiﬁcant only in samples with the highest permeability coefﬁcients (treatments 4 and 8). By increasing the wait time, it is possible that the polymer ﬁlm will slowly begin to solidify at the surface. In a study on modiﬁed PVDF membranes by Feng et al. [19], it was observed that long wait times resulted in membranes with a denser surface layer, fewer pores per area, and a ﬁnger-like cross-sectional structure. The structure results from the increased polymer concentration at the surface as the solvent evaporates, thereby inhibiting the rate at which the polymer can coagulate and the diffusion of the solvent out of the polymer. Membranes 2022, 12, 3 8 of 15 Figure 2. Average permeability coefﬁcients of 10% PVDF-g-EGMP membranes prepared with various casting conditions. Error bars represent 1 for ﬁve separate sample measurements. The inclusion of PVDF-g-EGMP within the membrane led to a signiﬁcant increase in water permeability. When PVDF membranes were cast under the same conditions without glycerol, observable permeate ﬂow was achieved only at pressures above 5 barg. Due to the negatively charged phosphate group in PVDF-g-EGMP, the copolymer membranes share similar structure to other ion-conducting polymers used to create polymer electrolyte membranes (PEMs) [20]. Prior studies on PEMs have observed an increase in wetting in membranes with long alkyl phosphonic chains [21]. It is likely that the phosphate group in PVDF-g-EGMP aids in the wetting of the pores in the copolymer membrane and increases water permeation. 3.3. Pu Uptake by PVDF-g-EGMP Copolymer Pu batch uptake studies were performed to evaluate the effectiveness of the PVDF- g-EGMP copolymer to extract Pu(VI) from water at pH 6.92 after 24 h of contact. Pu uptake was calculated by Equation (2). A A blank polymer Pu uptake = 100% (2) blank Pu uptake percentages of the PVDF and PVDF-g-EGMP was determined by 534K measuring the ﬁnal Pu activity (Bq) of solution in the empty (blank) vials (A ) and of blank 242 241 the vials containing polymer (A ). Due to the age of the Pu source, Am (daughter polymer 241 242 product of Pu decay) was present in the Pu solution and accounts for approximately 20% of the gross alpha activity in the solution. Activity measurements were performed on 242 241 the alpha spectrometer to distinguish Pu activity from Am, allowing for Equation (2) 241 242 241 to be used to determine Am uptake as well. Figure 3 shows the Pu and Am uptake values for the PVDF and PVDF-g-EGMP. Compared to PVDF , uptakes of Pu and 534K 534K Am were signiﬁcantly higher for PVDF-g-EGMP, resulting in near-complete uptake of Membranes 2022, 12, 3 9 of 15 the two actinides from solution under the test conditions. EGMP can bind Pu through ion exchange coordination depending on the solution conditions and pH. In acidic conditions, studies by Chappa et al. have shown that EGMP can coordinate with Pu through the phosphoryl and carbonyl oxygens as a bidentate ligand [22]. At higher pH, the phosphoric acid group becomes deprotonated (pK and pK values of 1.6 and 6.6) and is capable of a1 a2 cation exchange with Pu. The copolymer performed well for the uptake of Pu at a neutral pH due to EGMP acting as an ion-exchange site [23]. At the conditions tested, PVDF- g-EGMP appears to be non-selective between Pu(VI) and Am(III), but further sorption experiments will need to be done to evaluate whether the copolymer is selective for one actinide over the other. 242 241 Figure 3. Pu and Am uptake by PVDF and PVDF-g-EGMP samples from a solution containing 2.67 Bq/mL Pu at pH 6.92. Measurements were taken after 24 h contact with stirring. Error bars represent 1 for triplicate measurements. 3.4. Direct Flow Filtration and Alpha Spectrometry Measurements with 10% PVDF-g-EGMP Membranes Membranes composed of 10 wt% PVDF-g-EGMP were examined for their ability to extract Pu from water by direct ﬂow ﬁltration and to determine if Pu-loaded membranes can serve as samples for isotopic screening via alpha spectrometry following ﬁltration. Three membranes were prepared for the study. Following the formulations presented in Table 1, two sets of PVDF-g-EGMP membranes were cast with 0 and 2 wt% glycerol to create membranes with low and high permeabilities. A third set of membranes composed of 100% PVDF and cast with 2 wt% glycerol was used as a control for the study. Pu was chosen as the isotope as its higher speciﬁc activity allows for substantially lower mass concentrations of Pu to be screened. Pu-spiked DI water and synthetic seawater (further denoted as seawater) solutions were adjusted to a neutral pH and aged for 3 d to establish equilibrium between the Pu oxidation states. Prior to testing, the spiked DI water solution measured an activity of 0.48 0.01 Bq/mL (~3.2 10 M) at pH 6.61, and redox analysis indicated a composition of 34.2% Pu(IV) and 65.8% Pu(V). The activity of the seawater solution was measured to be 0.51 0.01 Bq/mL (~3.4 10 M) at pH 6.58 and was composed of 36.7% Pu(IV) and 63.3% Pu(V). Figure 4 shows Pu uptake percentages for the PVDF and PVDF-g-EGMP membranes. Highest Pu uptake percentages were observed for the PVDF-g-EGMP membranes cast without glycerol, with an average of 59.9 3.0% in DI water and 19.3 3.5% in seawater. Pu uptake from DI water was also high for the PVDF-g-EGMP membranes with glycerol at 41.3 17.1%. Despite the lower Pu uptake observed for the PVDF-g-EGMP mem- branes cast with 2 wt% glycerol, the increased permeability drastically reduced the time Membranes 2022, 12, 3 10 of 15 required for ﬁltration. At the same operating pressure, the copolymer membranes achieved ﬂowrates of 1.57 0.80 mL/min and 17.99 4.74 mL/min without and with the addition of glycerol. Figure 4. Pu uptake of 100% PVDF and 10% PVDF-g-EGMP membranes after ﬁltration of 10 mL of spiked deionized (DI) water (pH 6.61, 0.48 Bq/mL) and synthetic seawater (pH 6.58, 0.51 Bq/mL). Error bars represent 1 for three separate membranes. The overall decrease in Pu uptake in seawater likely resulted from two compounding factors: the presence of other ions that can compete for ion-exchange sites on EGMP and a change in the near-surface charge (zeta potential) of the membranes due to charge screening. The presence of other cations at high concentration potentially can reduce uptake of Pu and other actinides by EGMP. In a recent study by Suresh and Duval [24], adsorption isotherm experiments for uranyl and prominent seawater cations were performed with membranes consisting of an EGMP-based graft copolymer. Values for the equilibrium adsorption capacities and the Langmuir constants were reported for the cations after ﬁtting to a single- 2+ site Langmuir model. While the membranes exhibited a high sorption capacity for UO , 2+ 2+ 3+ + other divalent cations (Ca and Mg ), Fe and VO had similar or higher Langmuir constants. The study demonstrated that EGMP binds these ions, which reduces uptake of target actinides. Coulombic interactions between Pu ions and the membrane surface also are impacted by the high ionic strength of the seawater solution. At a neutral pH, pristine PVDF membranes have a negatively charged surface and exhibit a zeta potential of approximately 40 mV [25]. The negative surface charge attracts Pu cations towards the surface, resulting in the appreciable Pu uptake measured for pristine membranes. However, studies have shown that the zeta potential in PVDF membranes approaches a net zero charge as salt concentrations are increased. The reduction in the electrochemical boundary layer likely reduces the attraction of Pu ions to the surface of the membrane [26]. Isotopic analysis of the membranes was performed after ﬁltration, and Figure 5 shows the resulting alpha spectra for the DI water and seawater trials collected over 5 h. Due to retention of Pu on the negatively charged surface, the 100% PVDF membranes exhibit small but sharp alpha energy peaks for the radioisotope. In the DI water trials, spectra for membranes composed of 10 wt% PVDF-g-EGMP had higher Pu counts compared to the PVDF membranes. Despite differences in Pu uptake, the overall shape of the Pu photopeak was similar between PVDF-g-EGMP membranes cast without and with glycerol. Average peak energy resolutions were 48 keV FWHM for the copolymer membranes Membranes 2022, 12, 3 11 of 15 cast without glycerol (Figure 5C) and 32 keV FWHM for membranes cast with glycerol (Figure 5B). The PVDF-g-EGMP membranes exhibited broad tailing in the Pu photopeak that accounted for approximately 83% (no glycerol) and 85% (2 wt% glycerol) of the total 238 238 Pu activity measured. Despite the lower Pu uptake observed in the seawater trials, slight tailing was also observed in the PVDF-g-EGMP samples without glycerol (Figure 5F). Figure 5. Five-hour alpha spectra of 100% PVDF, 10 wt% PVDF-g-EGMP (2 wt% glycerol), and 10 wt% PVDF-g-EGMP (no glycerol) membranes after direct ﬁltration of Pu-bearing solutions. Measurements were taken after ﬁltering 10 mL of DI water (Spectra A–C, 0.48 Bq/mL Pu, pH 6.61) and synthetic seawater (Spectra D–F, 0.51 Bq/mL Pu, pH 6.58). The overall shape of the spectra seen in the copolymer membranes indicates that Pu sorption occurs on both the surface and pore walls of the membrane, resulting in a composite spectrum [27]. While Pu sorption to the surface creates a sharp photopeak, sorption to the pore walls results in broad tailing as the emitted alpha particles collide with the surrounding polymer before reaching the detector. We hypothesized that the amphiphilic structure of PVDF-g-EGMP would cause it to migrate to the surface during the casting of the membrane; however, if Pu sorption is occurring within the pore walls, it is likely that the graft copolymer is distributed throughout the depth of the membrane. To test this theory, SEM-EDS micrographs were taken of the membrane cross sections to determine the distribution of the PVDF-g-EGMP copolymer. SEM-EDS images for the PVDF-g-EGMP membranes are shown in Figure 6 (no glycerol) and Figure 7 (2 wt% glycerol). Locating PVDF-g-EGMP within the cross section was done by measuring P K (2.013 KeV) and O K (0.525 KeV) X-rays emitted from the phosphate and carboxylate ester groups found in EGMP. Images from the SEM-EDS analysis show that PVDF-g-EGMP Membranes 2022, 12, 3 12 of 15 appears to be distributed evenly throughout both membrane samples. The pore structure of the membrane can be observed clearly in the P K and O K micrographs for the 1 1 membranes cast without glycerol, indicating that the graft copolymer lines the pore walls. Figure 6. SEM-EDS images of 10 wt% PVDF-g-EGMP membranes cast without glycerol. Phosphorus (purple) and oxygen (yellow) distributions are shown for the region highlighted in the cross-sectional image. Average pore diameter was measured to be 0.098 0.027 m. Figure 7. SEM-EDS images of 10% PVDF-g-EGMP membranes cast with 2 wt% glycerol. Phosphorus (purple) and oxygen (yellow) distributions are shown for the region highlighted in the cross-sectional image. Average pore diameter was measured to be 0.338 0.066 m. While the even distribution of PVDF-g-EGMP throughout the membrane aids in the recovery of Pu overall, it impairs alpha spectrometry analysis; the peak tailing reduces Membranes 2022, 12, 3 13 of 15 its ability for high-resolution isotopic screening. However, changes to the synthesis of the PVDF-g-EGMP, as well as how the membrane is cast, can further promote surface migration of the copolymer within the membrane. Similar studies have been performed to promote the migration of amphiphilic copolymers to create a hydrophilic, fouling-resistant membrane surface [28]. Hester et al. [29] screened novel casting methods to promote surface migration of poly(MMA-r-POEM) in PVDF membranes. Surface concentrations of poly(MMA-r-POEM) were the highest when the membranes were coagulated in a hot water bath (~90 C) followed by 24 h annealing at 90 C, and it was speculated that the annealed membranes reached a maximum limit of copolymer surface coverage. In a later study, Hester and Mayes observed an increased surface concentration of poly(MMA-r-POEM) in a PVDF membrane when the molecular weight of the amphiphilic copolymer was increased [30]. Higher molecular weights of PVDF-g-EGMP can be achieved by allowing the ATRP reaction to proceed for longer durations, increasing the length of poly(EGMP) chains grafted from the PVDF anchor. This approach potentially may improve the resulting alpha spectra, as the higher ratio of EGMP to PVDF may promote segregation of the copolymer to the membrane surface during membrane formation. From a broader perspective, the functional membranes presented in this study could serve as extractive membrane adsorbers for actinide separations in lieu of resin-based chro- matography. Traditional resin columns rely on diffusion to drive target isotopes into the pores of the resin beads. At trace-level isotope concentrations, the diffusion driving force will be low, and the resin columns will require long residence times to achieve sufﬁcient levels of extraction. Alternatively, an extractive membrane adsorber allows for isotopes to be conveyed to the binding sites by convective ﬂow. For this application, the distribution of PVDF-g-EGMP along the pores of the membrane will improve the capacity for Pu and other actinides, and a bind-and-elute strategy can be developed for the sequential separation of each actinide from a mixed low-level source. A similar strategy can be adapted from elution procedures for commercial radiochromatography resins. Horwitz et al. devel- oped an elution procedure for mixed actinides using TRU resin (Eichrom Technologies, Lisle, IL, USA) containing octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine ox- ide (CMPO) in tri-N-butyl phosphate (TBP) [31]. The study demonstrated that tri-, tetra- and hexavalent actinides can be eluted sequentially from the resin using solutions com- posed of various concentrations of hydrochloric acid and other reagents. Other studies have demonstrated that EGMP-based copolymers can be regenerated over multiple bind- and-elution cycles for repeated use. In a study by Mhatre et al., thin ﬁlms composed poly(bis[2-(methacryloyloxy)ethyl] phosphate) (poly(BMEP) produced from a divinyl ester 4+ form of EGMP) did not exhibit any reduction in Pu recovery even after three desorption cycles with a solution composed of 1 M nitric acid and 0.2 M hydrazine hydrate and hydroxylamine [8]. For membranes containing PVDF-g-EGMP, it is likely that a similar desorption step can be performed to regenerate the membrane for multiple cycles. 4. Conclusions An ATRP procedure was developed to graft PEGMP from PVDF, creating a graft copolymer capable of extracting Pu from water at neutral pH conditions. The copolymer can be added to PVDF dope solutions to form membranes by nonsolvent induced phase separation for Pu capture and alpha spectrometry. Permeability studies with membranes composed of 10 wt% PVDF-g-EGMP indicated that water permeability improved with the addition of the copolymer, and a wide range of permeabilities was achieved by ad- justing casting conditions. The copolymer membranes exhibited Pu uptakes as high as 59.9 3.0% and 19.3 3.5% from DI water and synthetic seawater solutions that were passed through the membrane. SEM-EDS analysis showed that the graft copolymer was distributed throughout the depth of the membrane, leading to Pu peak tailing in the resulting alpha spectra. Future studies will investigate methods to increase the surface concentration of PVDF-g-EGMP within the membrane, including changes to the copoly- Membranes 2022, 12, 3 14 of 15 mer formulation and phase inversion procedure to promote surface migration during membrane formation. Supplementary Materials: The following are available online at https://www.mdpi.com/article/ 10.3390/membranes12010003/s1, Table S1: Isotopic fractions of the stock 147 Bq/mL solution; Table S2: Ion content of the synthetic seawater used in the direct ﬁltration Pu uptake studies; Table S3: Treatments for each batch of 10 wt% PVDF-g-EGMP membrane tested in the permeability study; Figure S1: Flux data for each 10 wt% PVDF-g-EGMP batch tested in the permeability study; Figure S2: Alpha spectrum of the 5 Bq Pu smear efﬁciency calibration sample; Figure S3: Alpha spectra of the 0.5 mL samples taken for the Pu uptake study; Figure S4: Sessile drop contact angle measurements of 100% PVDF membranes; Figure S5: Sessile drop contact angle measurements of PVDF membranes casted with 10% PVDF-g-EGMP. Author Contributions: Conceptualization, S.M.H. and T.A.D.; Methodology, J.C.F., S.M.H. and T.A.D.; Formal Analysis, J.C.F.; Investigation, J.C.F.; Resources, S.M.H. and T.A.D.; Data Curation, J.C.F.; Writing—Original Draft Preparation, J.C.F.; Writing—Review and Editing, S.M.H. and T.A.D.; Visualization, J.C.F.; Supervision, S.M.H. and T.A.D.; Project Administration, S.M.H. and T.A.D.; Funding Acquisition, S.M.H. and T.A.D. All authors have read and agreed to the published version of the manuscript. Funding: This work was supported by the Defense Threat Reduction Agency Basic Research Award #HDTRA1-16-1-0016. Institutional Review Board Statement: Not applicable. Informed Consent Statement: Not applicable. Data Availability Statement: The data required to reproduce these ﬁndings are available by request to the corresponding author. Acknowledgments: We thank Brian Powell for his procurement of Pu stock used in the study and Valery Bliznyuk and Joshua Osuofa for their insights on the polymerization approach. J.C.F. extends his thanks to George Wetzel and the staff members at the Clemson University Electron Microscopy Facility for their training and technical support on the SEM-EDS measurements. S.M.H. acknowledges support from the William B. “Bill” Sturgis, ‘57 and Martha Elizabeth “Martha Beth” Blackmon Sturgis Distinguished Professorship in Chemical and Biomolecular Engineering. Conﬂicts of Interest: The authors declare no conﬂict of interest. References 1. UNSCEAR. 2000 Report Vol. II: Sources and Effects of Ionizing Radiation; UNSCEAR: New York, NY, USA, 2000; pp. 518–520. 2. Moody, K.J.; Hutcheon, I.D.; Grant, P.M. Nuclear Forensic Analysis, 2nd ed.; CRC Press: New York, NY, USA, 2015; pp. 140–150. 3. Qiao, J.; Hou, X.; Miro, M.; Roos, P. Determination of Plutonium Isotopes in Waters and Environmental Solids: A Review. Anal. Chim. Acta 2009, 652, 66–84. [CrossRef] [PubMed] 4. Reis, A.S.; Temba, E.S.C.; Kastner, G.F.; Monteiró, R.P.G. Combined Procedure Using Radiochemical Separation of Plutonium, Americium, and Uranium Radionuclides for Alpha-Spectrometry. J. Radioanal. Nucl. Chem. 2011, 287, 567–572. [CrossRef] 5. Rim, J.H.; Gonzales, E.R.; Armenta, C.E.; Ünlü, K.; Peterson, D.S. Developing and Evaluating Di(2-ethylhexyl) Orthophosphoric Acid (HDEHP) Based Polymer Ligand Film (PLF) for Plutonium Extraction. J. Radioanal. Nucl. Chem. 2013, 296, 1099–1103. [CrossRef] 6. Gonzáles, E.R.; Kingensmith, A.L.; Peterson, D.S. Rapid Separation and Extraction of Radioactive Analytes onto Filters and Surfaces. Proc. Radiochem. 2011, 1, 195–200. [CrossRef] 7. Hanson, S.K.; Mueller, A.H.; Oldham, W.J. Kläui Ligand Thin Films for Rapid Plutonium Analysis by Alpha Spectrometry. Anal Chem. 2014, 86, 1153–1159. [CrossRef] [PubMed] 8. Mhatre, A.M.; Chappa, S.; Paul, S.; Pandey, A.K. Phosphate-Bearing Polymer Grafted Glass for Plutonium(IV) Ion-Selective Alpha Spectrometry. J. Anal. At. Spectrom. 2017, 32, 1566–1570. [CrossRef] 9. Locklair, W.D.; Mannion, J.M.; Husson, S.M.; Powell, B.A. Uptake of Plutonium on a Novel Thin Film for Use in Alpha Spectrometry. J. Radioanal. Nucl. Chem. 2016, 307, 2333–2338. [CrossRef] 10. Darge, A.W.; Gera, Y.; DeVol, T.A.; Husson, S.M. Uranium Concentration Using Reactive Polymer Thin Films for Spectroscopic Analysis. React. Funct. Polym. 2020, 157, 104761. [CrossRef] 11. Vasudevan, T.; Das, S.; Sodaye, S.; Pandey, A.K.; Reddy, A.V.R. Pore-Functionalized Polymer Membranes for Preconcentration of Heavy Metal Ions. Talanta 2009, 78, 171–177. [CrossRef] Membranes 2022, 12, 3 15 of 15 12. Duval, C.E.; Darge, A.W.; Ruff, C.; DeVol, T.A.; Husson, S.M. Rapid Sample Preparation for Alpha Spectroscopy with Ultraﬁltration Membranes. Anal. Chem. 2018, 90, 4144–4149. [CrossRef] 13. Foster, J.C.; DeVol, T.A.; Husson, S.M. Extractive Thin-Film Composite Membranes for the Isotopic Screening of Plutonium in Water. React. Funct. Polym. 2021, 167, M105020. [CrossRef] 14. Hester, J.F.; Banerjee, P.; Won, Y.Y.; Akthakul, A.; Acar, M.H.; Mayes, A.M. ATRP of Amphiphilic Graft Copolymers Based on PVDF and Their Use as Membrane Additives. Macromolecules 2002, 35, 7652–7661. [CrossRef] 15. Conroy, N.A.; Wylie, E.M.; Powell, B.A. A Novel Method for Tracer Concentration Plutonium(V) Solution Preparation. Anal. Chem. 2016, 88, 4196–4199. [CrossRef] 16. Das, S.; Pandey, A.K.; Vasudevan, T.; Athawale, A.A.; Manchanda, V.K. Adsorptive Preconcentration of Uranium in Hydrogels from Seawater and Aqueous Solutions. Ind. Eng. Chem. Res. 2009, 48, 6789–6796. [CrossRef] 17. Cai, X.; Lei, T.; Sun, D.; Lin, L. A Critical Analysis of the , , and Phases in Poly(vinylidene ﬂuoride) Using FTIR. RSC Adv. 2017, 7, 15382–15389. [CrossRef] 18. Gestring, I.; Mewes, D. Degassing of Molten Polymers. Chem. Eng. Sci. 2002, 57, 3415–3426. [CrossRef] 19. Feng, C.; Shi, B.; Li, G.; Wu, Y. Preparation and Properties of Microporous Membrane from Poly(vinylidene ﬂuoride-co- tetraﬂuoroethylene) (F2.4) for Membrane Distillation. J. Membr. Sci. 2004, 237, 15–24. [CrossRef] 20. Parvole, J.; Jannasch, P. Poly(arylene ether sulfone)s With Phosphonic Acid And Bis(phosphonic acid) on Short Alkyl Side Chains for Proton-Exchange Membranes. J. Mater. Chem. A 2008, 18, 5547–5556. [CrossRef] 21. Tamura, Y.; Sheng, L.; Nakazawa, S.; Higashihara, T.; Ueda, M. Polymer Electrolyte Membranes Based on Polystyrenes with Phosphonic Acid via Long Alkyl Side Chains. J. Polym. Sci. A Polym. Chem. 2012, 50, 4334–4340. [CrossRef] 22. Chappa, S.; Singha Deb, A.K.; Ali, S.M.; Debnath, A.K.; Aswal, D.K.; Pandey, A.K. Change in the Afﬁnity of Ethylene Gly- col Methacrylate Phosphate Monomer and its Polymer Anchored on a Graphene Oxide Platform towards Uranium(VI) and Plutonium(IV) ions. J. Phys. Chem. B 2016, 120, 2942–2950. [CrossRef] 23. Zhu, X.; Alexandratos, S.D. Development of a New Ion-Exchange/Coordinating Phosphate Ligand for the Sorption of U(VI) and Trivalent Ions from Phosphoric Acid Solutions. Chem. Eng. Sci. 2015, 127, 126–132. [CrossRef] 24. Suresh, P.; Duval, C.E. Poly(acid)-Functionalized Membranes to Sequester Uranium from Seawater. Ind. Eng. Chem. Res. 2020, 59, 12212–12222. [CrossRef] 25. Breite, D.; Went, M.; Prager, A.; Schulze, A. Tailoring Membrane Surface Charges: A Novel Study on Electrostatic Interactions during Membrane Fouling. Polymers 2015, 7, 2017–2030. [CrossRef] 26. Breite, D.; Went, M.; Prager, A.; Schulze, A. The Critical Zeta Potential of Polymer Membranes: How Electrolytes Impact Fouling. RSC Adv. 2016, 6, 98180–98189. [CrossRef] 27. Foster, J.C.; Starstrom, S.A.; DeVol, T.A.; Powell, B.A.; Husson, S.M. Functionalized Polymer Thin Films for Plutonium Capture and Isotopic Screening from Aqueous Sources. Anal. Chem. 2020, 92, 5214–5221. [CrossRef] [PubMed] 28. Stein, G.E.; Laws, T.S.; Verduzco, R. Tailoring the Attraction of Polymers Towards Surfaces. Macromolecules 2019, 52, 4748–4802. [CrossRef] 29. Hester, J.F.; Banerjee, P.; Mayes, A.M. Preparation of Protein-Resistant Surfaces on Poly(vinylidene ﬂuoride) Membranes via Surface Segregation. Macromolecules 1999, 32, 1643–1650. [CrossRef] 30. Hester, J.F.; Mayes, A.M. Design and Performance of Foul-Resistant Poly(vinylidene ﬂuoride) Membranes Prepared in a Single- Step by Surface Segregation. J. Membr. Sci. 2002, 202, 119–135. [CrossRef] 31. Horwitz, E.P.; Chiarizia, R.; Dietz, M.L.; Diamond, H. Separation and preconcentration of actinides from acidic media by extraction chromatography. Anal. Chim. Acta 1993, 281, 361–372. [CrossRef] http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.png Membranes Multidisciplinary Digital Publishing Institute http://www.deepdyve.com/lp/multidisciplinary-digital-publishing-institute/membranes-for-the-capture-and-screening-of-waterborne-plutonium-based-fXY270yC4B

Loading next page...

References (37)

Daniel Breite, Marco Went, A. Prager, Agnes Schulze, S. Husson (2015)
Tailoring Membrane Surface Charges: A Novel Study on Electrostatic Interactions during Membrane Fouling
Polymers, 7
J. Rim, E. Gonzáles, C. Armenta, K. Ünlü, D. Peterson (2013)
Developing and evaluating di(2-ethylhexyl) orthophosphoric acid (HDEHP) based polymer ligand film (PLF) for plutonium extraction
Journal of Radioanalytical and Nuclear Chemistry, 296
C. Duval, A. Darge, C. Ruff, T. Devol, S. Husson (2018)
Rapid Sample Preparation for Alpha Spectroscopy with Ultrafiltration Membranes.
Analytical chemistry, 90 6
Jonathan Hester, and Banerjee, A. Mayes (1999)
Preparation of Protein-Resistant Surfaces on Poly(vinylidene fluoride) Membranes via Surface Segregation
Macromolecules, 32
James Foster, T. Devol, S. Husson (2021)
Extractive thin-film composite membranes for the isotopic screening of plutonium in water
Reactive & Functional Polymers, 167
T. Vasudevan, Sadananda Das, S. Sodaye, A. Pandey, A. Reddy (2009)
Pore-functionalized polymer membranes for preconcentration of heavy metal ions.
Talanta, 78 1
A. Mhatre, S. Chappa, Sumana Paul, A. Pandey (2017)
Phosphate-bearing polymer grafted glass for plutonium(IV) ion-selective alpha spectrometry
Journal of Analytical Atomic Spectrometry, 32
Nations United (2000)
sources and effects of ionizing radiation
Jonathan Hester, P. Banerjee, You-Yeon Won, Ariya Akthakul, M. Acar, A. Mayes (2002)
ATRP of Amphiphilic Graft Copolymers Based on PVDF and Their Use as Membrane Additives
Macromolecules, 35
(2016)
Uptake of Plutonium on a Novel Thin Film for Use in Alpha Spectrometry
Julien Parvole, P. Jannasch (2008)
Poly(arylene ether sulfone)s with phosphonic acid and bis(phosphonic acid) on short alkyl side chains for proton-exchange membranes
Journal of Materials Chemistry, 18
(1993)
Separation and preconcentration of actinides from acidic media by extraction chromatography
Anal. Chim. Acta, 281
E. Gonzáles, A. Klingensmith, D. Peterson (2011)
Rapid separation and extraction of radioactive analytes onto filters and surfaces
Proceedings in Radiochemistry, 1
(2019)
Tailoring the Attraction of Polymers
(2015)
Nuclear Forensic Analysis, 2nd ed.; CRC
M. Dietz, D. Ensor, Benjamin Harmon, S. Seekamp (2006)
Separation and Preconcentration of Cesium from Acidic Media by Extraction Chromatography
Separation Science and Technology, 41
(2002)
Design and Performance of Foul-Resistant Poly(vinylidene fluoride) Membranes Prepared in a SingleStep by Surface Segregation
W. Kinard (2006)
Nuclear Forensic Analysis
Journal of Forensic Sciences, 51
Xiaoping Zhu, S. Alexandratos (2015)
Development of a new ion-exchange/coordinating phosphate ligand for the sorption of U(VI) and trivalent ions from phosphoric acid solutions
Chemical Engineering Science, 127
S. Hanson, A. Mueller, W. Oldham (2014)
Kläui ligand thin films for rapid plutonium analysis by alpha spectrometry.
Analytical chemistry, 86 2
(2016)
The Critical Zeta Potential of Polymer Membranes: How Electrolytes Impact Fouling
James Foster, Samantha Starstrom, T. Devol, B. Powell, S. Husson (2020)
Functionalized polymer thin films for plutonium capture and isotopic screening from aqueous sources.
Analytical chemistry
G. Stein, Travis Laws, R. Verduzco (2019)
Tailoring the Attraction of Polymers toward Surfaces
Macromolecules
Moody (2015)
140
Chunsheng Feng, Baoli Shi, Guomin Li, Yonglie Wu (2004)
Preparation and properties of microporous membrane from poly(vinylidene fluoride-co-tetrafluoroethylene) (F2.4) for membrane distillation
Journal of Membrane Science, 237
P. Suresh, C. Duval (2020)
Poly(acid)-Functionalized Membranes to Sequester Uranium from Seawater
Industrial & Engineering Chemistry Research
W. Locklair, J. Mannion, S. Husson, B. Powell (2016)
Uptake of plutonium on a novel thin film for use in spectrometry
Journal of Radioanalytical and Nuclear Chemistry, 307
S. Chappa, A. Deb, S. Ali, A. Debnath, D. Aswal, A. Pandey (2016)
Change in the Affinity of Ethylene Glycol Methacrylate Phosphate Monomer and Its Polymer Anchored on a Graphene Oxide Platform toward Uranium(VI) and Plutonium(IV) Ions.
The journal of physical chemistry. B, 120 11
J. Qiao, X. Hou, M. Miró, P. Roos (2009)
Determination of plutonium isotopes in waters and environmental solids: A review.
Analytica chimica acta, 652 1-2
Xiaomei Cai, T. Lei, Daoheng Sun, Liwei Lin (2017)
A critical analysis of the α, β and γ phases in poly(vinylidene fluoride) using FTIR
RSC Advances, 7
518
A. Reis, E. Temba, G. Kastner, R. Monteiro (2011)
Combined procedure using radiochemical separation of plutonium, americium and uranium radionuclides for alpha-spectrometry
Journal of Radioanalytical and Nuclear Chemistry, 287
A. Darge, Yugantar Gera, T. Devol, S. Husson (2020)
Uranium concentration using reactive polymer thin films for spectroscopic analyses
Reactive & Functional Polymers, 157
Youko Tamura, L. Sheng, S. Nakazawa, Tomoya Higashihara, M. Ueda (2012)
Polymer electrolyte membranes based on polystyrenes with phosphonic acid via long alkyl side chains
Journal of Polymer Science Part A, 50
N. Conroy, E. Wylie, B. Powell (2016)
A Novel Method for Tracer Concentration Plutonium(V) Solution Preparation.
Analytical chemistry, 88 8
I. Gestring, D. Mewes (2002)
Degassing of molten polymers
Chemical Engineering Science, 57
Sadananda Das, A. Pandey, T. Vasudevan, A. Athawale, V. Manchanda (2009)
Adsorptive Preconcentration of Uranium in Hydrogels from Seawater and Aqueous Solutions
Industrial & Engineering Chemistry Research, 48

Publisher: Multidisciplinary Digital Publishing Institute
Copyright: © 1996-2022 MDPI (Basel, Switzerland) unless otherwise stated Disclaimer The statements, opinions and data contained in the journals are solely those of the individual authors and contributors and not of the publisher and the editor(s). MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations. Terms and Conditions Privacy Policy
ISSN: 2077-0375
DOI: 10.3390/membranes12010003
Publisher site: See Article on Publisher Site

Abstract

membranes Article Membranes for the Capture and Screening of Waterborne Plutonium Based on a Novel Pu-Extractive Copolymer Additive 1 , 2 2 , 3 1 , James C. Foster , Timothy A. DeVol and Scott M. Husson * Department of Chemical and Biomolecular Engineering, Clemson University, 127 Earle Hall, Clemson, SC 29634, USA; jcf@clemson.edu Nuclear Environmental Engineering Sciences, Radioactive Waste Management Center, Clemson University, Clemson, SC 29625, USA; devol@clemson.edu Department of Environmental Engineering and Earth Sciences, Clemson University, 342 Computer Court, Anderson, SC 29625, USA * Correspondence: shusson@clemson.edu Abstract: This contribution describes the fabrication of plutonium-adsorptive membranes by non- solvent induced phase separation. The dope solution comprised poly(vinylidene ﬂuoride) (PVDF) and a Pu-extractive copolymer additive of PVDF-g-poly(ethylene glycol methacrylate phosphate) (EGMP) in dimethylformamide (DMF). The effects of casting conditions on membrane permeability were determined for PVDF membranes prepared with 10 wt% PVDF-g-EGMP. Direct-ﬂow ﬁltration and alpha spectrometry showed that membranes containing the graft copolymer could recover Pu up to 59.9 3.0% from deionized water and 19.3 3.5% from synthetic seawater after ﬁltering 10 mL of 0.5 Bq/mL Pu. SEM-EDS analysis indicated that the graft copolymer was distributed evenly throughout the entire depth of the copolymer membranes, likely attributing to the tailing observed in the alpha spectra for Pu. Despite the reduction in resolution, the membranes exhibited high Pu uptake at the conditions tested, and new membrane designs that promote copolymer surface Citation: Foster, J.C.; DeVol, T.A.; migration are expected to improve alpha spectrometry peak energy resolutions. Findings from this Husson, S.M. Membranes for the study also can be used to guide the development of extractive membranes for chromatographic Capture and Screening of Waterborne separation of actinides from contaminated groundwater sources. Plutonium Based on a Novel Pu-Extractive Copolymer Additive. Keywords: extractive membranes; nuclear forensics; plutonium isotopic screening; alpha spectrometry; Membranes 2022, 12, 3. https:// non-solvent induced phase separation doi.org/10.3390/membranes12010003 Academic Editors: Mohd Haﬁz Dzarfan Othman, Juhana Jaafar and Mukhlis A. Rahman 1. Introduction The development of rapid analytical tools for the detection of waterborne special Received: 26 November 2021 Accepted: 17 December 2021 nuclear materials is a critical focus of nuclear forensics efforts. Trace levels of Pu exist Published: 21 December 2021 in the environment as a result of human nuclear activity, and while weapons testing accounts for the largest source of Pu, accidental releases from nuclear power and nuclear Publisher’s Note: MDPI stays neutral processing facilities also have led to increased levels of Pu near those sites. The abundances with regard to jurisdictional claims in of Pu isotopes in each source act as a unique signature or “ﬁngerprint”, and the isotopic published maps and institutional afﬁl- ratios can indicate where the Pu was produced and its ﬁnal intended use. For example, iations. approximately 6.1 PBq (~20 kg) of Pu was released from the disaster at Chernobyl Nuclear 238 239 Power Plant in 1986, and it is estimated that the Pu consisted of 0.3% Pu, 66.9% Pu, 240 241 25.3% Pu, and 7.5% Pu by mass [1]. Unique Pu signatures also can be traced to a 240 239 Copyright: © 2021 by the authors. particular production facility, and the Pu/ Pu ratio can elucidate the intended use Licensee MDPI, Basel, Switzerland. for the produced Pu. The assembly of a ﬁssion-type nuclear weapon requires a reactor This article is an open access article design and operation to promote the growth of Pu while limiting the production of distributed under the terms and Pu. Generally, uranium target materials spend less time in the reactor and multiple conditions of the Creative Commons batch cycles followed by chemical reprocessing are needed to produce sufﬁcient Pu for Attribution (CC BY) license (https:// 239 a weapon [2]. Illicit proliferation of Pu is likely to leave trace levels of Pu in nearby creativecommons.org/licenses/by/ waters. Due to the low solubility and complex redox chemistry of waterborne Pu, direct 4.0/). Membranes 2022, 12, 3. https://doi.org/10.3390/membranes12010003 https://www.mdpi.com/journal/membranes Membranes 2022, 12, 3 2 of 15 measurements require a multi-step approach to perform isotopic analysis. Pu isolation and pre-concentration usually cannot be performed in the ﬁeld as it requires highly acidiﬁed or caustic solutions to separate Pu from a solution matrix. Therefore, an on-site analytical method that can concentrate Pu quickly to detectable limits while simultaneously screening for its isotopic abundance would be a valuable nuclear forensics tool. Instruments such as inductively coupled mass spectrometry (ICP-MS) and thermal ionization mass spectrometry (TIMS) are capable of screening for Pu isotopes at concen- trations as low as a few parts per billion; however, the size of these instruments and their respective equipment do not lend well for transport. Comparatively, an alpha spectrometer has the capability to be made into a ﬁeldable detection system for Pu and other alpha- emitters. For high resolution spectra, samples need to be dispersed thinly over a smooth surface to reduce alpha particle energy attenuation prior to reaching the detector. For this reason, electrodeposition remains the standard method for alpha spectrometry source preparation, as it can achieve peak resolutions (reported as full-width at half maximum, FWHM) from about 15 to 55 keV for Pu isotopes [3]. Preparing an electrodeposited Pu source from a contaminated water can be challenging and time-consuming as the Pu has to be isolated through separation techniques such as coprecipitation, liquid–liquid extraction or ion-exchange chromatography. Detection limits for alpha spectrometry are on the scale of 10 Bq, meaning that high volumes of a trace-level Pu solution would need to be processed to generate the activity needed for detection [4]. To reduce the time to prepare an alpha spectrometry source, we and others have turned to developing Pu extractive membranes that can concentrate Pu to detectable limits and serve directly as the sample source. Membranes are functionalized for Pu capture either by casting a polymer-ligand ﬁlm onto the membrane surface, or by utilizing a reactive surface from which a ligand layer can be grafted [5–10]. By keeping the functional layer relatively thin, high spectral resolutions can be achieved that rival electrodeposited sources. Careful consideration needs to be taken regarding the physical properties of the membrane support as the pore size and density affect overall throughput of a Pu-contaminated water source [10]. For nuclear forensics applications, the extractive membranes need to balance permeability, Pu uptake, and alpha spectrometry peak resolutions. Pu-binding ligands are chosen based on the approach used to incorporate them in or onto a membrane, and for their ability to complex with Pu depending on its oxidation state and solution conditions. Of relevance to the current study, membranes functionalized with ethylene glycol methacrylate phosphate (EGMP) have been shown to be capable of extracting Pu over a broad pH range. The phosphate group (with pK values of 1.6 and 6.6) can interact with Pu through ion-exchange or by chemical coordination. The dual functionality of EGMP was demonstrated in a study by Vasudevan et al., where polypropy- lene membranes grafted with EGMP recovered greater than 90% of Pu(IV) from solutions ranging from 0 to 4 M nitric acid [11]. Other studies have shown that membranes containing EGMP can serve directly as an alpha spectrometry sample source for actinides. Duval et al. developed a method to graft EGMP from polyethersulfone membranes for the isotopic screening of waterborne uranium. After ﬁltering solutions spiked with U, the modiﬁed membranes achieved U peak resolutions ranging from 17 to 33 keV FWHM [12]. Further- more, the peak resolutions achieved by the membranes were sharp enough to distinguish 238 234 U (4.198 MeV) from U (4.775 MeV) after ﬁltering a spiked groundwater source at pH 6. In our previous study [13], extractive thin-ﬁlm composite (e-TFC) membranes were developed for the rapid capture and isotopic screening of Pu in water. The e-TFC mem- branes were made by spin coating a thin copolymer ﬁlm consisting of 5% (w/w) EGMP and 4-methylstyrene (a.k.a. vinyltoluene, VT) onto a poly(vinylidene ﬂuoride) (PVDF) ultraﬁltration membrane. Direct ﬂow ﬁltration studies indicated that the e-TFC mem- 242 242 branes recovered up to 10.2 4.2% of Pu after ﬁltering 10 mL of a 4.53 Bq/mL Pu solution at pH 6.8, and the 16 h alpha spectra exhibited average energy resolutions of 71.7 8.7 keV for the Pu peak. While spin coating provided a simple and effective way to cast a Pu-selective polymer onto a membrane, the addition of the poly(EGMP-co-VT) Membranes 2022, 12, 3 3 of 15 layer greatly reduced the overall permeability of the membrane. At trace-level Pu con- 12 10 centrations (10 to 10 M), the reduced permeability of the e-TFC membranes poses concern as the membranes need to be able to process large volumes of solution rapidly to reach alpha spectrometry detection limits. The aim of this study was to develop a Pu-extractive membrane with high permeability for rapid concentration and alpha spectroscopy analysis of trace-level Pu from water. For high alpha spectra energy resolution, the extractive functional layer should be thin and able to sequester Pu onto the surface of the membrane. The method for membrane fabrication was inspired by the approach used by Hester et al. [14] to develop fouling-resistant graft copolymer membranes. They demonstrated that hydrophilic poly(oxyethylene methacry- late) (POEM) and poly(methacrylic acid) (PMAA) could be grafted directly by atom transfer radical polymerization (ATRP) from the secondary ﬂuorinated sites in PVDF. This created amphiphilic copolymers consisting of a hydrophobic PVDF anchor with a hydrophilic POEM or PMAA comb shell. PVDF membranes were prepared by nonsolvent induced phase separation (NIPS) using dope solutions containing 5–10 wt% PVDF-g-POEM. It was observed that the amphiphilic nature of the copolymer would lead it to segregate to the membrane surface upon formation. In membranes containing 10 wt% PVDF-g-POEM, the surface migration greatly improved the wetting of the membrane and reduced protein adsorption over seven-fold compared to PVDF membranes. This study demonstrated a simple approach to casting functional membranes without the need for post-modiﬁcation steps. Here, we used ATRP to graft EGMP from PVDF. We theorized that the addition of this Pu-selective PVDF-g-EGMP copolymer in the dope solution during membrane formation by NIPS would yield a high permeability, Pu-extractive membrane. We theorized further that, given the hydrophilicity of EGMP, the graft copolymer would migrate to the surface of the membrane where it would concentrate Pu during ﬁltration and enable high spectral resolution when the membrane is screened in an alpha spectrometer. 2. Materials and Methods 2.1. Materials The following chemicals were purchased from MilliporeSigma (St. Louis, MO, USA): copper(I) chloride (CuCl, 97%); dimethylformamide (DMF, 99.8%); inhibitor remover (alu- minum oxide, activated); methanol (95%); n-methyl-2-pyrrolidone (NMP, 99.5%); phospho- ric acid 2-hydroxyethyl methacrylate ester (further denoted as ethylene glycol methacrylate phosphate, EGMP, 90%); PVDF (M ~250,000 g/mol); PVDF (M ~534,000 g/mol); w w 250K 534K and tris(2-pyridyl methyl) amine (TPMA, 98%). Chemicals purchased from Fisher Sci- entiﬁc (Waltham, MA, USA) were nitric acid (HNO , 65% w/w); petroleum ether (ACS reagent, 35–60 C boiling range); and sodium hydroxide (NaOH, 97%). Instant Ocean Synthetic Sea Salt was purchased from Carolina Biological Supply Company (Burlington, NC, USA). Nitrogen gas and dry air was from Airgas (Radnor, PA, USA). Type-1 deionized (DI) water was produced using a Millipore Milli-Q Reference water puriﬁcation system (Darmstadt, Germany). 242 242 2+ Pu solutions were prepared from a 147 Bq/mL Pu(VI) (PuO ) stock in 1 mM HNO provided by Dr. Brian Powell (Clemson University, Department of Environmental Engineering and Earth Sciences). Low-activity solutions were diluted from the stock with DI water, followed by conditioning with 0.1 and 1 M aliquots of HNO and NaOH to achieve circumneutral pH conditions immediately prior to use. Table S1 in Supplementary Materials reports mass fractions of the Pu isotopes in the stock solution. For the direct ﬂow ﬁltration study, Pu solutions were prepared by dilution in DI water and synthetic seawater from a NIST traceable Pu stock (Eckert & Ziegler, Valencia, CA, USA) with an activity of 2464 Bq/mL in 0.1 M HNO . The dilutions were conditioned with 0.1 and 1 M aliquots of HNO and NaOH to adjust the pH to circumneutral conditions. The solutions were set aside for 3 d to allow for equilibrium between Pu oxidation states. Synthetic seawater was prepared using Instant Ocean Synthetic Sea Salt to replicate typical seawater conditions. Table S2 in Supplementary Materials provides the composition of Membranes 2022, 12, 3 4 of 15 the solution. Pu oxidation states of the Pu dilutions were determined through a solvent extraction method outlined by Powell et al. [15]. 2.2. Synthesis of PVDF-g-EGMP Copolymer Prior to copolymer synthesis, monomethyl ether hydroquinone was removed from the EGMP by combining 1 g EGMP and 20 mg inhibitor remover and stirring for at least 1 h. A Cu-TPMA solution was prepared by dissolving 40 mg CuCl and 180 mg TPMA in 5 mL NMP under an inert N atmosphere in a glovebox (MBRAUN, Garching, Germany). An EGMP solution was prepared in a Schlenk ﬂask by dissolving 15 g EGMP in 20 mL NMP. In a separate Schlenk ﬂask, 5 g PVDF was dissolved in 30 mL NMP. Dissolved 250K air was removed from the EGMP and PVDF solutions through a freeze-pump-thaw 250K procedure. First, the ﬂasks were sealed and placed in a liquid nitrogen bath until the contents were frozen solid. A vacuum line was attached, and the ﬂasks were submerged in a 75 C water bath while under vacuum to thaw. This process was repeated for at least three cycles, or until visible air bubbles were no longer formed during the thawing step. The EGMP and PVDF solutions were left sealed under vacuum until further use. 250K ATRP grafting of EGMP from PVDF was performed in the N glove box where the Cu- TPMA solution was stored. The prepared EGMP and PVDF solutions were combined 250K in a reaction vessel and heated to 90 C stirring by a magnetic stir bar at 300 RPM. Once the set temperature was reached, the Cu-TPMA solution was added to the reaction mixture, and the ATRP reaction proceeded for 24 h. Afterwards, the reaction vessel was removed from the glove box. PVDF-g-EGMP was precipitated from solution with a mixture of 50 mL methanol and 100 mL petroleum ether. To remove unreacted EGMP monomer, the precipitated PVDF-g-EGMP was dissolved again in NMP, followed by precipitation with the methanol/petroleum ether mixture. The copolymer was dried for at least 24 h in a fume hood at room temperature. Characterization of PVDF-g-EGMP was done by attenuated total reﬂectance Fourier-transform infrared spectroscopy (ATR-FTIR) on a PerkinElmer Spectrum II equipped with a diamond crystal. Spectra were generated from 32 scans at a resolution of 8 cm using PerkinElmer Spectrum 10 software. 2.3. Screening of PVDF-g-EGMP Copolymer for Pu Uptake Pu-uptake measurements were performed with PVDF-g-EGMP to quantify Pu uptake 242 242 from solutions at neutral pH conditions. A Pu(VI) solution was diluted from the Pu stock to produce a solution with a ﬁnal activity of 2.67 Bq/mL and pH 6.92. One hundred milligrams of the PVDF-g-EGMP copolymer was placed in a 1.5 mL vial with 1 mL of the Pu solution. The sample was stirred for 24 h on a Stuart SB2 rotator (Staffordshire, UK) set to 20 RPM. Afterwards, 0.5 mL of solution from each sample was removed and pipetted onto a 30 mm diameter steel planchette. Once planchettes were dry, they were placed 5 mm from the detector face in an alpha spectrometer and counted for 5 h. A control study was performed by repeating the study with PVDF in-lieu of the grafted copolymer, and Pu 534K sorption to the vials was accounted for by performing the experiment with empty vials. All sample trials were performed in triplicate measurements to determine average values and standard deviations for Pu uptake. 2.4. Casting PVDF Membranes with PVDF-g-EGMP Grafted copolymer membranes were cast from dope solutions using the formulations shown in Table 1, designed to produce membranes composed of approximately 10 wt% PVDF-g-EGMP. Dope solutions were prepared by dissolving PVDF and PVDF-g-EGMP 534K in DMF for 24 h under stirring, or until the polymer was fully dissolved. To study the effects of permeability on Pu uptake and alpha spectra peak resolution, glycerol was added to the dope solutions at 2 wt% to increase the porosity of the membranes. Membranes 2022, 12, 3 5 of 15 Table 1. Compositions of the dope solutions prepared for casting poly(vinylidene ﬂuoride) (PVDF) membrane composed of 10% PVDF-g-EGMP (ethylene glycol methacrylate phosphate) in dimethyl- formamide (DMF). Membrane Dope Solutions DMF PVDF PVDF-g-EGMP Glycerol 534K Membrane [g] [g] [g] [g] 10% PVDF-g-EGMP No glycerol 47.2 7.5 0.83 0 10% PVDF-g-EGMP 2 wt% glycerol 46.1 7.5 0.83 1.11 Membrane formation was achieved through NIPS. Prior to membrane casting, the polymer dope solutions were vacuum degassed at 75 kPa to remove any dissolved air from solution. The solutions were cast onto a clean glass plate and drawn using a doctor blade (Gardco, Pompano Beach, FL, USA) set to a height of 0.18 mm. Five seconds after drawing, the glass plate was immersed in a DI water bath for at least 2 min, resulting in the complete coagulation of the membrane onto the glass plate. Afterwards, the membranes were removed from the bath and stored in fresh DI water until further use. 2.5. Permeability Studies Grafted copolymer membranes were cut to 45 mm diameter coupons and placed in a Sterlitech HP4750 ﬂow cell (Kent, WA, USA). The cell was ﬁlled with DI water and sealed. Prior to measurements, the ﬂow cell was pressurized to 4.14 barg for 15 min to condition the membrane prior to taking measurements. Afterwards, the operating pressure was reduced to 0.69 barg. Flux measurements were taken at four setpoints as the pressure was increased from 1.38 to 3.45 barg. At each pressure setpoint, ﬁltrate mass and ﬂow time were recorded to determine water ﬂux and permeability. After the ﬁrst pressure cycle, cell pressure was reduced to 0.69 barg, and measurements were taken over a second pressure ramp to observe whether hysteresis occurred. For each membrane casting condition studied, average permeability values and uncertainty were calculated from ﬁve membrane samples. 2.6. SEM Analysis of Membrane Morphologies Scanning electron microscopy imaging with electron dispersive spectroscopy (SEM- EDS) was performed on the copolymer membranes to visualize morphology and locate where PVDF-g-EGMP copolymer resides within the membrane structure. Prior to measure- ments, membrane samples were washed sequentially for 1 h increments in water/ethanol solutions consisting of 25, 50, and 75 wt% ethanol. After drying from the 75 wt% ethanol solution, the samples were mounted to an aluminum holder with carbon tape. Samples were prepared so that the topside and cross-section morphologies could be analyzed. To analyze the membrane cross-section, samples were submerged in liquid nitrogen, freeze fractured, and mounted to the aluminum holder with the fractured edge exposed. Samples for topside surface imaging were coated with platinum for 40 min using an Anatech Hummer 6.5 sputter coater (Sparks, NV, USA). Micrographs were taken of the membrane surfaces using a Hitachi Regulus 8230 SEM (Tokyo, Japan) at an accelerating voltage of 2 kV. For the cross-sectional samples, platinum coating was not required; instead, the samples were measured on a Hitachi SU5000 SEM equipped with an Oxford Instru- ments X-Max 80 silicon drift detector for EDS (High Wycombe, UK). The samples were screened at an accelerating voltage of 10 kV, and chemical imaging of the cross-section was performed using AztectLive v3.3 software (Oxford Instruments, High Wycombe, UK). Pore size diameter measurements were averaged over twenty pores using ImageJ image analysis software, freely available online from the National Institutes of Health (Bethesda, MD, USA). Membranes 2022, 12, 3 6 of 15 2.7. Alpha Spectrometry Measurements Alpha spectrometry was performed using an Ortec 7401 alpha spectrometer (Oak Ridge, TN, USA) equipped with a 450 mm passivated ion silicon detector (PIPS). Peak energy calibration was performed with a 30 mm diameter Eckert & Ziegler electrodeposited source 234 238 239 241 containing known quantities of U, U, Pu, and Am. The calibration source was placed 5 mm from the PIPS detector and counted for 1 h. Absolute detector efﬁciency was determined for the 45 mm diameter membranes by spotting 5 Bq of the stock Pu solution onto the surface of a PVDF membrane. The droplets were carefully smeared across the membrane surface using a pipette tip. Once dry, the membrane was ﬁxed into a custom acrylic holder and placed 5 mm away from the PIPs detector to be counted for 1 h. 2.8. Direct Flow Filtration of Pu Solutions through PVDF-g-EGMP Membranes Membranes cast with 10 wt% PVDF-g-EGMP were cut into 45 mm diameter coupons and placed in a Amicon ultraﬁltration cell (EMD Millipore, Burlington, MA, USA). Two Pu solutions were prepared for the study: a spiked DI water solution with an activity of 0.48 0.01 Bq/mL and pH 6.61, and a synthetic seawater solution with an activity of 0.51 0.01 Bq/mL and pH 6.58. Filtration and alpha spectrometry procedures were the same for DI water and synthetic seawater trials. The Amicon ﬂow cell was ﬁlled with 10 mL of the prepared Pu solution. The cell was sealed and pressurized to 0.69 barg using a dry air cylinder to start ﬁltration. Once all of the Pu solution was ﬁltered, the cell was reﬁlled with 10 mL DI water and pressurized to 0.69 barg to perform a wash cycle to remove Pu from the membrane pores. The membrane was removed once the cell was completely empty of its contents and depressurized. Membrane samples were dried for at least 1 h before alpha spectrometry measurements. Alpha spectrometry was performed by mounting the membranes in a custom acrylic holder placed 5 mm from the detector face, followed by counting for 5 h. 3. Results 3.1. PVDF-g-EGMP Synthesis and Characterization FTIR analysis was performed on the PVDF-g-EGMP copolymer to determine if it exhibited characteristic peaks of EGMP. Figure 1 shows FTIR spectra for the graft copolymer, along with EGMP and PVDF precursors. Distinct peaks for the two precursors were observed in the graft copolymer, indicating successful grafting of EGMP from the PVDF macroinitiator. Characteristic absorbance peaks for EGMP were noted at 1720 and 980 cm assigned to C=O and P=O stretching, while peaks at 1400 and 880 cm correspond to vibrational bands observed in semi-crystalline PVDF [16,17]. 3.2. Permeability Measurements of PVDF-g-EGMP Membranes Direct-ﬂow water permeability measurements were carried out for the 10 wt% PVDF- g-EGMP copolymer membranes. Casting conditions were varied to determine the effects on membrane permeabilities. The copolymer membranes were cast (1) with or without vacuum degassing of the polymer solution prior to casting; (2) with or without the addition of 2 wt% glycerol; and (3) by waiting a short (5 s) or long (30 s) period between casting and submerging into the coagulation bath. Casting conditions are summarized in Table S3, and the resulting water ﬂux data for each membrane are given in Figure S1. The linear relationship between water ﬂux and transmembrane pressure is given by Equation (1), where J represents water ﬂux (in L/m /h, further denoted as LMH), A is the permeability coefﬁcient (LMH/bar), and DP is the transmembrane pressure (bar). J = ADP (1) Membranes 2022, 12, 3 7 of 15 Figure 1. Attenuated-total reﬂectance Fourier-transform infraredspectra of the PVDF-g-EGMP copoly- mer, EGMP monomer, and PVDF used in atom transfer radical polymerization (ATRP)grafting. Figure 2 shows the average permeability coefﬁcients for each membrane, along with the conditions used to prepare the membranes. The permeability of the membranes in- creased with the incorporation of glycerol and when the copolymer dope solution was not degassed by vacuum prior to casting. The increase in permeability for non-degassed samples was likely due to dissolved air present in the membrane casting solutions, poten- tially leading to the formation of voids during the coagulation process. Degassing is often a critical step in phase inversion processes as it prevents the formation of microbubbles as the polymer begins to solidify [18]. To determine whether the short or long wait times affected the overall permeability of the copolymer membranes, comparisons were made between treatments using a two-tailed separate-variance (Welch’s) t-test. At an level of 0.05, it was observed for the two wait times that differences in permeability were signiﬁcant only in samples with the highest permeability coefﬁcients (treatments 4 and 8). By increasing the wait time, it is possible that the polymer ﬁlm will slowly begin to solidify at the surface. In a study on modiﬁed PVDF membranes by Feng et al. [19], it was observed that long wait times resulted in membranes with a denser surface layer, fewer pores per area, and a ﬁnger-like cross-sectional structure. The structure results from the increased polymer concentration at the surface as the solvent evaporates, thereby inhibiting the rate at which the polymer can coagulate and the diffusion of the solvent out of the polymer. Membranes 2022, 12, 3 8 of 15 Figure 2. Average permeability coefﬁcients of 10% PVDF-g-EGMP membranes prepared with various casting conditions. Error bars represent 1 for ﬁve separate sample measurements. The inclusion of PVDF-g-EGMP within the membrane led to a signiﬁcant increase in water permeability. When PVDF membranes were cast under the same conditions without glycerol, observable permeate ﬂow was achieved only at pressures above 5 barg. Due to the negatively charged phosphate group in PVDF-g-EGMP, the copolymer membranes share similar structure to other ion-conducting polymers used to create polymer electrolyte membranes (PEMs) [20]. Prior studies on PEMs have observed an increase in wetting in membranes with long alkyl phosphonic chains [21]. It is likely that the phosphate group in PVDF-g-EGMP aids in the wetting of the pores in the copolymer membrane and increases water permeation. 3.3. Pu Uptake by PVDF-g-EGMP Copolymer Pu batch uptake studies were performed to evaluate the effectiveness of the PVDF- g-EGMP copolymer to extract Pu(VI) from water at pH 6.92 after 24 h of contact. Pu uptake was calculated by Equation (2). A A blank polymer Pu uptake = 100% (2) blank Pu uptake percentages of the PVDF and PVDF-g-EGMP was determined by 534K measuring the ﬁnal Pu activity (Bq) of solution in the empty (blank) vials (A ) and of blank 242 241 the vials containing polymer (A ). Due to the age of the Pu source, Am (daughter polymer 241 242 product of Pu decay) was present in the Pu solution and accounts for approximately 20% of the gross alpha activity in the solution. Activity measurements were performed on 242 241 the alpha spectrometer to distinguish Pu activity from Am, allowing for Equation (2) 241 242 241 to be used to determine Am uptake as well. Figure 3 shows the Pu and Am uptake values for the PVDF and PVDF-g-EGMP. Compared to PVDF , uptakes of Pu and 534K 534K Am were signiﬁcantly higher for PVDF-g-EGMP, resulting in near-complete uptake of Membranes 2022, 12, 3 9 of 15 the two actinides from solution under the test conditions. EGMP can bind Pu through ion exchange coordination depending on the solution conditions and pH. In acidic conditions, studies by Chappa et al. have shown that EGMP can coordinate with Pu through the phosphoryl and carbonyl oxygens as a bidentate ligand [22]. At higher pH, the phosphoric acid group becomes deprotonated (pK and pK values of 1.6 and 6.6) and is capable of a1 a2 cation exchange with Pu. The copolymer performed well for the uptake of Pu at a neutral pH due to EGMP acting as an ion-exchange site [23]. At the conditions tested, PVDF- g-EGMP appears to be non-selective between Pu(VI) and Am(III), but further sorption experiments will need to be done to evaluate whether the copolymer is selective for one actinide over the other. 242 241 Figure 3. Pu and Am uptake by PVDF and PVDF-g-EGMP samples from a solution containing 2.67 Bq/mL Pu at pH 6.92. Measurements were taken after 24 h contact with stirring. Error bars represent 1 for triplicate measurements. 3.4. Direct Flow Filtration and Alpha Spectrometry Measurements with 10% PVDF-g-EGMP Membranes Membranes composed of 10 wt% PVDF-g-EGMP were examined for their ability to extract Pu from water by direct ﬂow ﬁltration and to determine if Pu-loaded membranes can serve as samples for isotopic screening via alpha spectrometry following ﬁltration. Three membranes were prepared for the study. Following the formulations presented in Table 1, two sets of PVDF-g-EGMP membranes were cast with 0 and 2 wt% glycerol to create membranes with low and high permeabilities. A third set of membranes composed of 100% PVDF and cast with 2 wt% glycerol was used as a control for the study. Pu was chosen as the isotope as its higher speciﬁc activity allows for substantially lower mass concentrations of Pu to be screened. Pu-spiked DI water and synthetic seawater (further denoted as seawater) solutions were adjusted to a neutral pH and aged for 3 d to establish equilibrium between the Pu oxidation states. Prior to testing, the spiked DI water solution measured an activity of 0.48 0.01 Bq/mL (~3.2 10 M) at pH 6.61, and redox analysis indicated a composition of 34.2% Pu(IV) and 65.8% Pu(V). The activity of the seawater solution was measured to be 0.51 0.01 Bq/mL (~3.4 10 M) at pH 6.58 and was composed of 36.7% Pu(IV) and 63.3% Pu(V). Figure 4 shows Pu uptake percentages for the PVDF and PVDF-g-EGMP membranes. Highest Pu uptake percentages were observed for the PVDF-g-EGMP membranes cast without glycerol, with an average of 59.9 3.0% in DI water and 19.3 3.5% in seawater. Pu uptake from DI water was also high for the PVDF-g-EGMP membranes with glycerol at 41.3 17.1%. Despite the lower Pu uptake observed for the PVDF-g-EGMP mem- branes cast with 2 wt% glycerol, the increased permeability drastically reduced the time Membranes 2022, 12, 3 10 of 15 required for ﬁltration. At the same operating pressure, the copolymer membranes achieved ﬂowrates of 1.57 0.80 mL/min and 17.99 4.74 mL/min without and with the addition of glycerol. Figure 4. Pu uptake of 100% PVDF and 10% PVDF-g-EGMP membranes after ﬁltration of 10 mL of spiked deionized (DI) water (pH 6.61, 0.48 Bq/mL) and synthetic seawater (pH 6.58, 0.51 Bq/mL). Error bars represent 1 for three separate membranes. The overall decrease in Pu uptake in seawater likely resulted from two compounding factors: the presence of other ions that can compete for ion-exchange sites on EGMP and a change in the near-surface charge (zeta potential) of the membranes due to charge screening. The presence of other cations at high concentration potentially can reduce uptake of Pu and other actinides by EGMP. In a recent study by Suresh and Duval [24], adsorption isotherm experiments for uranyl and prominent seawater cations were performed with membranes consisting of an EGMP-based graft copolymer. Values for the equilibrium adsorption capacities and the Langmuir constants were reported for the cations after ﬁtting to a single- 2+ site Langmuir model. While the membranes exhibited a high sorption capacity for UO , 2+ 2+ 3+ + other divalent cations (Ca and Mg ), Fe and VO had similar or higher Langmuir constants. The study demonstrated that EGMP binds these ions, which reduces uptake of target actinides. Coulombic interactions between Pu ions and the membrane surface also are impacted by the high ionic strength of the seawater solution. At a neutral pH, pristine PVDF membranes have a negatively charged surface and exhibit a zeta potential of approximately 40 mV [25]. The negative surface charge attracts Pu cations towards the surface, resulting in the appreciable Pu uptake measured for pristine membranes. However, studies have shown that the zeta potential in PVDF membranes approaches a net zero charge as salt concentrations are increased. The reduction in the electrochemical boundary layer likely reduces the attraction of Pu ions to the surface of the membrane [26]. Isotopic analysis of the membranes was performed after ﬁltration, and Figure 5 shows the resulting alpha spectra for the DI water and seawater trials collected over 5 h. Due to retention of Pu on the negatively charged surface, the 100% PVDF membranes exhibit small but sharp alpha energy peaks for the radioisotope. In the DI water trials, spectra for membranes composed of 10 wt% PVDF-g-EGMP had higher Pu counts compared to the PVDF membranes. Despite differences in Pu uptake, the overall shape of the Pu photopeak was similar between PVDF-g-EGMP membranes cast without and with glycerol. Average peak energy resolutions were 48 keV FWHM for the copolymer membranes Membranes 2022, 12, 3 11 of 15 cast without glycerol (Figure 5C) and 32 keV FWHM for membranes cast with glycerol (Figure 5B). The PVDF-g-EGMP membranes exhibited broad tailing in the Pu photopeak that accounted for approximately 83% (no glycerol) and 85% (2 wt% glycerol) of the total 238 238 Pu activity measured. Despite the lower Pu uptake observed in the seawater trials, slight tailing was also observed in the PVDF-g-EGMP samples without glycerol (Figure 5F). Figure 5. Five-hour alpha spectra of 100% PVDF, 10 wt% PVDF-g-EGMP (2 wt% glycerol), and 10 wt% PVDF-g-EGMP (no glycerol) membranes after direct ﬁltration of Pu-bearing solutions. Measurements were taken after ﬁltering 10 mL of DI water (Spectra A–C, 0.48 Bq/mL Pu, pH 6.61) and synthetic seawater (Spectra D–F, 0.51 Bq/mL Pu, pH 6.58). The overall shape of the spectra seen in the copolymer membranes indicates that Pu sorption occurs on both the surface and pore walls of the membrane, resulting in a composite spectrum [27]. While Pu sorption to the surface creates a sharp photopeak, sorption to the pore walls results in broad tailing as the emitted alpha particles collide with the surrounding polymer before reaching the detector. We hypothesized that the amphiphilic structure of PVDF-g-EGMP would cause it to migrate to the surface during the casting of the membrane; however, if Pu sorption is occurring within the pore walls, it is likely that the graft copolymer is distributed throughout the depth of the membrane. To test this theory, SEM-EDS micrographs were taken of the membrane cross sections to determine the distribution of the PVDF-g-EGMP copolymer. SEM-EDS images for the PVDF-g-EGMP membranes are shown in Figure 6 (no glycerol) and Figure 7 (2 wt% glycerol). Locating PVDF-g-EGMP within the cross section was done by measuring P K (2.013 KeV) and O K (0.525 KeV) X-rays emitted from the phosphate and carboxylate ester groups found in EGMP. Images from the SEM-EDS analysis show that PVDF-g-EGMP Membranes 2022, 12, 3 12 of 15 appears to be distributed evenly throughout both membrane samples. The pore structure of the membrane can be observed clearly in the P K and O K micrographs for the 1 1 membranes cast without glycerol, indicating that the graft copolymer lines the pore walls. Figure 6. SEM-EDS images of 10 wt% PVDF-g-EGMP membranes cast without glycerol. Phosphorus (purple) and oxygen (yellow) distributions are shown for the region highlighted in the cross-sectional image. Average pore diameter was measured to be 0.098 0.027 m. Figure 7. SEM-EDS images of 10% PVDF-g-EGMP membranes cast with 2 wt% glycerol. Phosphorus (purple) and oxygen (yellow) distributions are shown for the region highlighted in the cross-sectional image. Average pore diameter was measured to be 0.338 0.066 m. While the even distribution of PVDF-g-EGMP throughout the membrane aids in the recovery of Pu overall, it impairs alpha spectrometry analysis; the peak tailing reduces Membranes 2022, 12, 3 13 of 15 its ability for high-resolution isotopic screening. However, changes to the synthesis of the PVDF-g-EGMP, as well as how the membrane is cast, can further promote surface migration of the copolymer within the membrane. Similar studies have been performed to promote the migration of amphiphilic copolymers to create a hydrophilic, fouling-resistant membrane surface [28]. Hester et al. [29] screened novel casting methods to promote surface migration of poly(MMA-r-POEM) in PVDF membranes. Surface concentrations of poly(MMA-r-POEM) were the highest when the membranes were coagulated in a hot water bath (~90 C) followed by 24 h annealing at 90 C, and it was speculated that the annealed membranes reached a maximum limit of copolymer surface coverage. In a later study, Hester and Mayes observed an increased surface concentration of poly(MMA-r-POEM) in a PVDF membrane when the molecular weight of the amphiphilic copolymer was increased [30]. Higher molecular weights of PVDF-g-EGMP can be achieved by allowing the ATRP reaction to proceed for longer durations, increasing the length of poly(EGMP) chains grafted from the PVDF anchor. This approach potentially may improve the resulting alpha spectra, as the higher ratio of EGMP to PVDF may promote segregation of the copolymer to the membrane surface during membrane formation. From a broader perspective, the functional membranes presented in this study could serve as extractive membrane adsorbers for actinide separations in lieu of resin-based chro- matography. Traditional resin columns rely on diffusion to drive target isotopes into the pores of the resin beads. At trace-level isotope concentrations, the diffusion driving force will be low, and the resin columns will require long residence times to achieve sufﬁcient levels of extraction. Alternatively, an extractive membrane adsorber allows for isotopes to be conveyed to the binding sites by convective ﬂow. For this application, the distribution of PVDF-g-EGMP along the pores of the membrane will improve the capacity for Pu and other actinides, and a bind-and-elute strategy can be developed for the sequential separation of each actinide from a mixed low-level source. A similar strategy can be adapted from elution procedures for commercial radiochromatography resins. Horwitz et al. devel- oped an elution procedure for mixed actinides using TRU resin (Eichrom Technologies, Lisle, IL, USA) containing octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine ox- ide (CMPO) in tri-N-butyl phosphate (TBP) [31]. The study demonstrated that tri-, tetra- and hexavalent actinides can be eluted sequentially from the resin using solutions com- posed of various concentrations of hydrochloric acid and other reagents. Other studies have demonstrated that EGMP-based copolymers can be regenerated over multiple bind- and-elution cycles for repeated use. In a study by Mhatre et al., thin ﬁlms composed poly(bis[2-(methacryloyloxy)ethyl] phosphate) (poly(BMEP) produced from a divinyl ester 4+ form of EGMP) did not exhibit any reduction in Pu recovery even after three desorption cycles with a solution composed of 1 M nitric acid and 0.2 M hydrazine hydrate and hydroxylamine [8]. For membranes containing PVDF-g-EGMP, it is likely that a similar desorption step can be performed to regenerate the membrane for multiple cycles. 4. Conclusions An ATRP procedure was developed to graft PEGMP from PVDF, creating a graft copolymer capable of extracting Pu from water at neutral pH conditions. The copolymer can be added to PVDF dope solutions to form membranes by nonsolvent induced phase separation for Pu capture and alpha spectrometry. Permeability studies with membranes composed of 10 wt% PVDF-g-EGMP indicated that water permeability improved with the addition of the copolymer, and a wide range of permeabilities was achieved by ad- justing casting conditions. The copolymer membranes exhibited Pu uptakes as high as 59.9 3.0% and 19.3 3.5% from DI water and synthetic seawater solutions that were passed through the membrane. SEM-EDS analysis showed that the graft copolymer was distributed throughout the depth of the membrane, leading to Pu peak tailing in the resulting alpha spectra. Future studies will investigate methods to increase the surface concentration of PVDF-g-EGMP within the membrane, including changes to the copoly- Membranes 2022, 12, 3 14 of 15 mer formulation and phase inversion procedure to promote surface migration during membrane formation. Supplementary Materials: The following are available online at https://www.mdpi.com/article/ 10.3390/membranes12010003/s1, Table S1: Isotopic fractions of the stock 147 Bq/mL solution; Table S2: Ion content of the synthetic seawater used in the direct ﬁltration Pu uptake studies; Table S3: Treatments for each batch of 10 wt% PVDF-g-EGMP membrane tested in the permeability study; Figure S1: Flux data for each 10 wt% PVDF-g-EGMP batch tested in the permeability study; Figure S2: Alpha spectrum of the 5 Bq Pu smear efﬁciency calibration sample; Figure S3: Alpha spectra of the 0.5 mL samples taken for the Pu uptake study; Figure S4: Sessile drop contact angle measurements of 100% PVDF membranes; Figure S5: Sessile drop contact angle measurements of PVDF membranes casted with 10% PVDF-g-EGMP. Author Contributions: Conceptualization, S.M.H. and T.A.D.; Methodology, J.C.F., S.M.H. and T.A.D.; Formal Analysis, J.C.F.; Investigation, J.C.F.; Resources, S.M.H. and T.A.D.; Data Curation, J.C.F.; Writing—Original Draft Preparation, J.C.F.; Writing—Review and Editing, S.M.H. and T.A.D.; Visualization, J.C.F.; Supervision, S.M.H. and T.A.D.; Project Administration, S.M.H. and T.A.D.; Funding Acquisition, S.M.H. and T.A.D. All authors have read and agreed to the published version of the manuscript. Funding: This work was supported by the Defense Threat Reduction Agency Basic Research Award #HDTRA1-16-1-0016. Institutional Review Board Statement: Not applicable. Informed Consent Statement: Not applicable. Data Availability Statement: The data required to reproduce these ﬁndings are available by request to the corresponding author. Acknowledgments: We thank Brian Powell for his procurement of Pu stock used in the study and Valery Bliznyuk and Joshua Osuofa for their insights on the polymerization approach. J.C.F. extends his thanks to George Wetzel and the staff members at the Clemson University Electron Microscopy Facility for their training and technical support on the SEM-EDS measurements. S.M.H. acknowledges support from the William B. “Bill” Sturgis, ‘57 and Martha Elizabeth “Martha Beth” Blackmon Sturgis Distinguished Professorship in Chemical and Biomolecular Engineering. Conﬂicts of Interest: The authors declare no conﬂict of interest. References 1. UNSCEAR. 2000 Report Vol. II: Sources and Effects of Ionizing Radiation; UNSCEAR: New York, NY, USA, 2000; pp. 518–520. 2. Moody, K.J.; Hutcheon, I.D.; Grant, P.M. Nuclear Forensic Analysis, 2nd ed.; CRC Press: New York, NY, USA, 2015; pp. 140–150. 3. Qiao, J.; Hou, X.; Miro, M.; Roos, P. Determination of Plutonium Isotopes in Waters and Environmental Solids: A Review. Anal. Chim. Acta 2009, 652, 66–84. [CrossRef] [PubMed] 4. Reis, A.S.; Temba, E.S.C.; Kastner, G.F.; Monteiró, R.P.G. Combined Procedure Using Radiochemical Separation of Plutonium, Americium, and Uranium Radionuclides for Alpha-Spectrometry. J. Radioanal. Nucl. Chem. 2011, 287, 567–572. [CrossRef] 5. Rim, J.H.; Gonzales, E.R.; Armenta, C.E.; Ünlü, K.; Peterson, D.S. Developing and Evaluating Di(2-ethylhexyl) Orthophosphoric Acid (HDEHP) Based Polymer Ligand Film (PLF) for Plutonium Extraction. J. Radioanal. Nucl. Chem. 2013, 296, 1099–1103. [CrossRef] 6. Gonzáles, E.R.; Kingensmith, A.L.; Peterson, D.S. Rapid Separation and Extraction of Radioactive Analytes onto Filters and Surfaces. Proc. Radiochem. 2011, 1, 195–200. [CrossRef] 7. Hanson, S.K.; Mueller, A.H.; Oldham, W.J. Kläui Ligand Thin Films for Rapid Plutonium Analysis by Alpha Spectrometry. Anal Chem. 2014, 86, 1153–1159. [CrossRef] [PubMed] 8. Mhatre, A.M.; Chappa, S.; Paul, S.; Pandey, A.K. Phosphate-Bearing Polymer Grafted Glass for Plutonium(IV) Ion-Selective Alpha Spectrometry. J. Anal. At. Spectrom. 2017, 32, 1566–1570. [CrossRef] 9. Locklair, W.D.; Mannion, J.M.; Husson, S.M.; Powell, B.A. Uptake of Plutonium on a Novel Thin Film for Use in Alpha Spectrometry. J. Radioanal. Nucl. Chem. 2016, 307, 2333–2338. [CrossRef] 10. Darge, A.W.; Gera, Y.; DeVol, T.A.; Husson, S.M. Uranium Concentration Using Reactive Polymer Thin Films for Spectroscopic Analysis. React. Funct. Polym. 2020, 157, 104761. [CrossRef] 11. Vasudevan, T.; Das, S.; Sodaye, S.; Pandey, A.K.; Reddy, A.V.R. Pore-Functionalized Polymer Membranes for Preconcentration of Heavy Metal Ions. Talanta 2009, 78, 171–177. [CrossRef] Membranes 2022, 12, 3 15 of 15 12. Duval, C.E.; Darge, A.W.; Ruff, C.; DeVol, T.A.; Husson, S.M. Rapid Sample Preparation for Alpha Spectroscopy with Ultraﬁltration Membranes. Anal. Chem. 2018, 90, 4144–4149. [CrossRef] 13. Foster, J.C.; DeVol, T.A.; Husson, S.M. Extractive Thin-Film Composite Membranes for the Isotopic Screening of Plutonium in Water. React. Funct. Polym. 2021, 167, M105020. [CrossRef] 14. Hester, J.F.; Banerjee, P.; Won, Y.Y.; Akthakul, A.; Acar, M.H.; Mayes, A.M. ATRP of Amphiphilic Graft Copolymers Based on PVDF and Their Use as Membrane Additives. Macromolecules 2002, 35, 7652–7661. [CrossRef] 15. Conroy, N.A.; Wylie, E.M.; Powell, B.A. A Novel Method for Tracer Concentration Plutonium(V) Solution Preparation. Anal. Chem. 2016, 88, 4196–4199. [CrossRef] 16. Das, S.; Pandey, A.K.; Vasudevan, T.; Athawale, A.A.; Manchanda, V.K. Adsorptive Preconcentration of Uranium in Hydrogels from Seawater and Aqueous Solutions. Ind. Eng. Chem. Res. 2009, 48, 6789–6796. [CrossRef] 17. Cai, X.; Lei, T.; Sun, D.; Lin, L. A Critical Analysis of the , , and Phases in Poly(vinylidene ﬂuoride) Using FTIR. RSC Adv. 2017, 7, 15382–15389. [CrossRef] 18. Gestring, I.; Mewes, D. Degassing of Molten Polymers. Chem. Eng. Sci. 2002, 57, 3415–3426. [CrossRef] 19. Feng, C.; Shi, B.; Li, G.; Wu, Y. Preparation and Properties of Microporous Membrane from Poly(vinylidene ﬂuoride-co- tetraﬂuoroethylene) (F2.4) for Membrane Distillation. J. Membr. Sci. 2004, 237, 15–24. [CrossRef] 20. Parvole, J.; Jannasch, P. Poly(arylene ether sulfone)s With Phosphonic Acid And Bis(phosphonic acid) on Short Alkyl Side Chains for Proton-Exchange Membranes. J. Mater. Chem. A 2008, 18, 5547–5556. [CrossRef] 21. Tamura, Y.; Sheng, L.; Nakazawa, S.; Higashihara, T.; Ueda, M. Polymer Electrolyte Membranes Based on Polystyrenes with Phosphonic Acid via Long Alkyl Side Chains. J. Polym. Sci. A Polym. Chem. 2012, 50, 4334–4340. [CrossRef] 22. Chappa, S.; Singha Deb, A.K.; Ali, S.M.; Debnath, A.K.; Aswal, D.K.; Pandey, A.K. Change in the Afﬁnity of Ethylene Gly- col Methacrylate Phosphate Monomer and its Polymer Anchored on a Graphene Oxide Platform towards Uranium(VI) and Plutonium(IV) ions. J. Phys. Chem. B 2016, 120, 2942–2950. [CrossRef] 23. Zhu, X.; Alexandratos, S.D. Development of a New Ion-Exchange/Coordinating Phosphate Ligand for the Sorption of U(VI) and Trivalent Ions from Phosphoric Acid Solutions. Chem. Eng. Sci. 2015, 127, 126–132. [CrossRef] 24. Suresh, P.; Duval, C.E. Poly(acid)-Functionalized Membranes to Sequester Uranium from Seawater. Ind. Eng. Chem. Res. 2020, 59, 12212–12222. [CrossRef] 25. Breite, D.; Went, M.; Prager, A.; Schulze, A. Tailoring Membrane Surface Charges: A Novel Study on Electrostatic Interactions during Membrane Fouling. Polymers 2015, 7, 2017–2030. [CrossRef] 26. Breite, D.; Went, M.; Prager, A.; Schulze, A. The Critical Zeta Potential of Polymer Membranes: How Electrolytes Impact Fouling. RSC Adv. 2016, 6, 98180–98189. [CrossRef] 27. Foster, J.C.; Starstrom, S.A.; DeVol, T.A.; Powell, B.A.; Husson, S.M. Functionalized Polymer Thin Films for Plutonium Capture and Isotopic Screening from Aqueous Sources. Anal. Chem. 2020, 92, 5214–5221. [CrossRef] [PubMed] 28. Stein, G.E.; Laws, T.S.; Verduzco, R. Tailoring the Attraction of Polymers Towards Surfaces. Macromolecules 2019, 52, 4748–4802. [CrossRef] 29. Hester, J.F.; Banerjee, P.; Mayes, A.M. Preparation of Protein-Resistant Surfaces on Poly(vinylidene ﬂuoride) Membranes via Surface Segregation. Macromolecules 1999, 32, 1643–1650. [CrossRef] 30. Hester, J.F.; Mayes, A.M. Design and Performance of Foul-Resistant Poly(vinylidene ﬂuoride) Membranes Prepared in a Single- Step by Surface Segregation. J. Membr. Sci. 2002, 202, 119–135. [CrossRef] 31. Horwitz, E.P.; Chiarizia, R.; Dietz, M.L.; Diamond, H. Separation and preconcentration of actinides from acidic media by extraction chromatography. Anal. Chim. Acta 1993, 281, 361–372. [CrossRef]

Journal

Membranes – Multidisciplinary Digital Publishing Institute

Published: Dec 21, 2021

Keywords: extractive membranes; nuclear forensics; plutonium isotopic screening; alpha spectrometry; non-solvent induced phase separation

Get 20M+ Full-Text Papers For Less Than $1.50/day. Start a 14-Day Trial for You or Your Team.

Learn More →

Membranes for the Capture and Screening of Waterborne Plutonium Based on a Novel Pu-Extractive Copolymer Additive

Membranes for the Capture and Screening of Waterborne Plutonium Based on a Novel Pu-Extractive Copolymer Additive

Get 20M+ Full-Text Papers For Less Than $1.50/day. Start a 14-Day Trial for You or Your Team.

Learn More →

Membranes for the Capture and Screening of Waterborne Plutonium Based on a Novel Pu-Extractive Copolymer Additive

Membranes for the Capture and Screening of Waterborne Plutonium Based on a Novel Pu-Extractive Copolymer Additive

References (37)

Abstract

Journal

Recommended Articles

There are no references for this article.

Our policy towards the use of cookies