Access the full text.
Sign up today, get DeepDyve free for 14 days.
K. Kimoto, R. Xie, Y. Matsui, K. Ishizuka, N. Hirosaki (2009)
Direct observation of single dopant atom in light-emitting phosphor of β-SiAlON:Eu2+Applied Physics Letters, 94
G. Zschornack (2007)
Handbook of X-Ray Data
Gunji, Kamimura (1996)
First-principles study on metal-doped icosahedral B12 solids.Physical review. B, Condensed matter, 54 19
Nilanjan Chatterjee (2020)
Electron Microprobe AnalysisDefinitions
M. Terauchi, S. Koshiya, K. Kimito (2018)
Information observed in Ti-Lα,β and Ti-Lℓ,η emission lines of Ti and its oxidesIOP Conference Series: Materials Science and Engineering, 304
C. MacRae, M. Pearce, N. Wilson, A. Torpy, M. Glenn, S. Russo (2020)
Soft X-Ray and Cathodoluminescence Examination of a Tanzanian Graphite DepositMicroscopy and Microanalysis, 26
K. Tsuda, Michiyoshi Tanaka (2016)
Direct observation of the symmetry breaking of the nanometer-scale local structure in the paraelectric cubic phase of BaTiO3 using convergent-beam electron diffractionApplied Physics Express, 9
M. Terauchi (2014)
Valence Electron Spectroscopy for Transmission Electron Microscopy
J. Etourneau, P. Hagenmuller (1985)
Structure and physical features of the rare-earth boridesPhilosophical Magazine Part B, 52
Z. Yin, J. Rehanek, H. Löchel, C. Braig, J. Buck, A. Firsov, J. Viefhaus, A. Erko, S. Techert (2017)
Highly efficient soft X-ray spectrometer based on a reflection zone plate for resonant inelastic X-ray scattering measurements.Optics express, 25 10
M. Terauchi, S. Koshiya, F. Satoh, Hideyuki Takahashi, N. Handa, T. Murano, M. Koike, T. Imazono, M. Koeda, T. Nagano, H. Sasai, Y. Oue, Z. Yonezawa, S. Kuramoto (2014)
Chemical State Information of Bulk Specimens Obtained by SEM-Based Soft-X-Ray Emission SpectrometryMicroscopy and Microanalysis, 20
M. Terauchi, Yohei Sato, Masatoshi Takeda (2021)
Chemical State Mapping of Bulk Materials by Electron Microscopy Based Soft X-ray Emission Spectroscopy, 60
J. Nagamatsu, N. Nakagawa, T. Muranaka, Y. Zenitani, J. Akimitsu (2001)
Superconductivity at 39 K in magnesium diborideNature, 410
M. Terauchi, H. Yamamoto, M. Tanaka (2001)
Development of a sub-eV resolution soft-X-ray spectrometer for a transmission electron microscope.Journal of electron microscopy, 50 2
O. Krivanek, T. Lovejoy, N. Dellby, T. Aoki, R. Carpenter, P. Rez, Emmanuel Soignard, Jiangtao Zhu, P. Batson, Maureen Lagos, Ray Egerton, P. Crozier, LeRoy Eyring (2014)
Vibrational spectroscopy in the electron microscopeNature, 514
Yohei Sato, M. Terauchi, K. Adachi (2012)
High energy-resolution electron energy-loss spectroscopy study on the near-infrared scattering mechanism of Cs0.33WO3 crystals and nanoparticlesJournal of Applied Physics, 112
T. Nagatochi, H. Hyodo, A. Sumiyoshi, K. Soga, Yohei Sato, M. Terauchi, F. Esaka, K. Kimura (2011)
Superconductivity in Li-doped α-rhombohedral boronPhysical Review B, 83
M. Takeda, M. Terui, Norihito Takahashi, N. Ueda (2006)
Improvement of thermoelectric properties of alkaline-earth hexaboridesJournal of Solid State Chemistry, 179
M. Terauchi (2019)
Information of valence charge of 3d transition metal elements observed in L-emission spectra.Microscopy
H. Niedrig, E. Rau (1998)
Information depth and spatial resolution in BSE microtomography in SEMNuclear Instruments & Methods in Physics Research Section B-beam Interactions With Materials and Atoms, 142
Xinan Zhang, Binghao Wang, Wei Huang, Yao Chen, Gang Wang, Li Zeng, Weigang Zhu, M. Bedzyk, Weifeng Zhang, J. Medvedeva, A. Facchetti, T. Marks (2018)
Synergistic Boron Doping of Semiconductor and Dielectric Layers for High-Performance Metal Oxide Transistors: Interplay of Experiment and Theory.Journal of the American Chemical Society, 140 39
R. Kasada, Y. Ha, T. Higuchi, K. Sakamoto (2016)
Chemical State Mapping of Degraded B4C Control Rod Investigated with Soft X-ray Emission Spectrometer in Electron Probe Micro-analysisScientific Reports, 6
Hideyuki Takahashi, T. Murano, M. Takakura, Shunsuke Asahina, M. Terauchi, M. Koike, T. Imazono, M. Koeda, T. Nagano (2016)
Development of soft X-ray emission spectrometer for EPMA/SEM and its applicationIOP Conference Series: Materials Science and Engineering, 109
Hideyuki Takahashi, N. Handa, T. Murano, M. Terauchi, M. Koike, T. Imazono, N. Hasegawa, M. Koeda, T. Nagano, H. Sasai, Y. Oue, Z. Yonezawa, S. Kuramoto (2013)
Chemical State Mapping via Soft X-rays using a Wavelength Dispersive Soft X-ray Emission Spectrometer with High Energy ResolutionMicroscopy and Microanalysis, 19
J. Scheifers, Yuemei Zhang, B. Fokwa (2017)
Boron: Enabling Exciting Metal-Rich Structures and Magnetic Properties.Accounts of chemical research, 50 9
M. Terauchi, M. Kawana (2006)
Soft-X-ray emission spectroscopy based on TEM-Toward a total electronic structure analysis.Ultramicroscopy, 106 11-12
(2014)
Synthesis and Characterization of p‐type CaB6
Liang Shi, Yunle Gu, Luyang Chen, Zeheng Yang, Jianhua Ma, Yitai Qian (2003)
Low Temperature Synthesis and Characterization of Cubic CaB6 Ultrafine Powders.ChemInform, 35
J. Haga, N. Mizui, T. Nagamichi, A. Okamoto (1998)
Effect of Boron on Mechanical Properties and Recrystallization Behavior of Ti-added Ultra-low Carbon Cold-rolled Steel SheetsIsij International, 38
B. Albert, H. Hillebrecht (2009)
Boron: elementary challenge for experimenters and theoreticians.Angewandte Chemie, 48 46
M. Takeda, T. Fukuda, Ferrer Domingo, T. Miura (2004)
Thermoelectric properties of some metal boridesJournal of Solid State Chemistry, 177
Shingo Ishii, M. Terauchi, Yohei Sato, N. Tamura, M. Aono, H. Abe (2018)
Soft X-ray emission spectroscopy study of characteristic bonding states and its distribution of amorphous carbon-nitride (a-CNx) films.Microscopy
K. Mukai, R. Kasada, K. Yabuuchi, S. Konishi, Jae-Hwan Kim, M. Nakamichi (2019)
Valence Electron and Chemical State Analysis of Be12M (M = Ti, V) Beryllides by Soft X-ray Emission SpectroscopyACS Applied Energy Materials
J. Bearden (1967)
X-Ray WavelengthsReviews of Modern Physics, 39
J. Yanch (1995)
Current status of Neutron Capture Therapy in the United StatesRadiotherapy and Oncology, 37
applied sciences Article Chemical State Mapping of p/n-Controlled SrB Bulk Specimens by Soft X-ray Emission Electron Microscope 1 , 1 2 Masami Terauchi *, Yohei K. Sato and Masatoshi Takeda Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2–1–1 Katahira, Aoba-ku, Sendai 980–8577, Japan; yohei.sato.c4@tohoku.ac.jp Department of Mechanical Engineering, Nagaoka University of Technology, 1603–1 Kamitomioka, Nagaoka 940–2188, Japan; takeda@mech.nagaokaut.ac.jp * Correspondence: m_terauchi@tohoku.ac.jp; Tel.: +81-(0)2-2217-5372 Featured Application: Nondestructive functional imaging of bulk specimens by soft X-ray emis- sion electron microscopy. Abstract: Elemental and chemical state maps of p/n-controlled SrB bulk specimens are presented by using a soft X-ray emission spectroscopy electron microscope. Those bulk specimens were obtained by sintering powder specimens, prepared by the molten-salt method with different compositions of initial materials. A Sr-map, a chemical shift map of B K-emission, and the spectra of characteristic regions of those materials were compared. It was observed that a local Sr deficiency caused a local hole-doped region, confirmed by a chemical shift in the B K-emission spectrum. n-type SrB was rather homogeneous. On the other hand, the p-type SrB bulk specimen was a mixture of two different p-type regions. This mixed nature originated, presumably, from an uneven Sr content of SrB particles prepared by the molten-salt method using a Sr-deficient starting material. A separation process of Citation: Terauchi, M.; Sato, Y.K.; the two types of materials will realize a high-quality homogeneous p-type SrB bulk specimens. Takeda, M. Chemical State Mapping 6 of p/n-Controlled SrB Bulk Keywords: soft X-ray emission spectroscopy microscope; chemical shift map; hole-doping; elemental Specimens by Soft X-ray Emission Electron Microscope. Appl. Sci. 2021, map; spectrum imaging 11, 9588. https://doi.org/10.3390/ app11209588 Academic Editors: Yohei Uemura, 1. Introduction Kiyofumi Nitta and Hiroki Wadati Recent developments in new functional materials, with the help of theoretical sim- ulations and data science, could accelerate practical applications of these new functional Received: 10 September 2021 materials. For progressing those practical applications, not only improved and effective ma- Accepted: 9 October 2021 terial processing methods, but also quick feedback of the evaluated results of the structure, Published: 14 October 2021 composition, and chemical state of new products are necessary. Dedicated transmission electron microscope (TEM) is a powerful candidate for evaluating the structure and chemi- Publisher’s Note: MDPI stays neutral cal characteristics of materials, with a nanometer-scale spatial resolution [1–4]. However, with regard to jurisdictional claims in it is a destructive inspection process due to a necessity of thin specimens of about tens of published maps and institutional affil- nanometers for transmission experiments. For a nondestructive inspection process with iations. a high spatial resolution, evaluations based on scanning electron microscopy are useful. A soft X-ray emission spectroscopy (SXES) instrument, combined with a scanning electron microscope (SEM) and/or an electron probe microanalyzer (EPMA) can realize a nonde- structive inspection process of the chemical state of materials, with a spatial resolution of Copyright: © 2021 by the authors. about 1 m or better [5–7]. If this occurs, SXES microscopy can make a quick feedback loop Licensee MDPI, Basel, Switzerland. of the evaluated results of new products for materials processing. This article is an open access article The chemical state analysis of boron is a topical issue in materials science. Boron forms distributed under the terms and four allotropes of , -rhombohedral boron and , -tetragonal boron. These materials have conditions of the Creative Commons a three-dimensional network of boron clusters. -rhombohedral boron is expected to be a Attribution (CC BY) license (https:// superconductor by electron doping [8,9]. Boron compounds also express interesting char- creativecommons.org/licenses/by/ acteristics as metals, semiconductors, insulators, and superconductors [10–12]. In addition, 4.0/). Appl. Sci. 2021, 11, 9588. https://doi.org/10.3390/app11209588 https://www.mdpi.com/journal/applsci Appl. Sci. 2021, 11, 9588 2 of 9 boron is one of the key chemical species as a fine additive element in the production of functional tuff steel, magnetic materials, the formation of fundamental switches for large integrated circuits, medical applications, etc. [13–16] The alkaline-earth hexaborides CaB , SrB , and BaB are candidate materials for 6 6 6 thermoelectric conversion because of their large Seebeck coefficients and electrical conduc- tivities [17,18]. Each material is composed of a three-dimensional network of B octagonal clusters, placed at each corner of a cubic unit cell, and an incorporated alkaline-earth metal atom at the body-center position of the unit cell. The metal atom can transfer two valence electrons to the B cluster network, resulting in an n-type semiconductor. For realizing a thermoelectric device using B cluster network materials, a p-type semiconductor is necessary. As Na atoms only have one valence electron, Na substitution to the Ca site of CaB (Na-doped CaB ) is a hole-doping to the B cluster network, causing a p-type semi- 6 6 6 conductor as a bulk [19]. This p-type Na-doped CaB was evaluated by using a commercial SXES-EPMA instrument, which reported an inhomogeneous charge distribution due to a compositional fluctuation in the bulk [20]. p/n-type controlled CaB bulk materials, pre- pared by the molten-salt method with starting materials containing different compositional ratios of Ca and B, were also examined by SXES-EPMA. It was revealed that the produced p-type bulk CaB specimen included locally n-type regions [21]. In this report, nondestructive chemical state evaluations of p/n-controlled SrB bulk specimens are presented. Two-dimensional spectral mapping of the soft X-ray emission spectra of these materials gives information of elemental inhomogeneity, and the related hole-doping nature appears as a chemical shift in the spectra of the material. 2. Methods and Materials 2.1. Chemical State Information by SXES Electron-beam-induced X-ray emission was used for elemental analysis by using an X-ray energy dispersive spectroscopy (EDS) instrument, and elemental and partial chemical analyses were performed using an EPMA. Among those X-rays, X-rays due to transitions from valence bands (bonding state) to inner-shell levels, usually lower than 1 keV, have information about the chemical bonding states of elements. Recent soft X-ray emission spectrometry using gratings, which was first developed for TEM [22–24] and then transferred to SEM and EPMA [5–7], has an energy resolution better than 1 eV, which is about two orders better than that of EDS and allowed us to obtain chemical bonding information by using X-ray emission. Another spectrometer system for soft X-rays is under examination [25]. Figure 1 shows the electronic transitions in a material caused by electron beam ir- radiation. Firstly, incident electrons excite electrons, a and b. This automatically causes energy losses of the incident electrons, which is the physical quantity to be measured in electron-energy-loss spectroscopy in TEM. The excited material quickly returns to the ground state. In the de-excitation process, downward electronic transitions of c and d to inner-shell core-hole states, which were created by the excitation process b, occur by accompanying X-ray emissions under a dipole-selection rule condition. Both emissions of c and d in Figure 1 are used in elemental analysis. However, only the X-ray emissions caused by the transition c includes information about the energy distribution of bonding electrons, the density of states of valence bands (VB). Thus, X-rays due to transitions c are a sensitive tool for chemical state analysis. As the energy spread of VB is smaller than 10 eV, an energy resolution better than 1 eV is necessary for obtaining information of chemical bonding states by SXES. Appl. Sci. 2021, 11, 9588 3 of 9 Figure 1. Electronic transitions related to electron energy-loss spectroscopy, a and b, and X-ray emission spectroscopy, c and d. Only X-ray emissions due to transitions c include a chemical bonding information. Figure 2a shows a schematic figure of the SXES mapping system used. The SXES sys- tem (JEOL SS-94000SXES), which is composed of varied-line-spacing gratings (aberration- corrected gratings) and a CCD detector, was attached to an EPMA (JEOL JXA-8230). The distance from the specimen to the detector was about 50 cm. The combination of the two VLS gratings of JS50XL and JS200N covers 50–210 eV for the 1st-order diffraction lines, and 100–420 eV for the 2nd-order diffraction lines [7]. The energy resolution of about 0.2 eV was realized for the 1st-order Al L-emission at about 73 eV. Figure 2b shows the 1st-order B K-emission (corresponds to transition c in Figure 1) spectra of pure boron ( -rhombohedral boron, -r-B), CaB , AlB , and hexagonal-BN (h-BN). N-K(2) in the h-BN 6 2 spectrum is the 2nd-order line of N K-emission, which shows a larger intensity than B K-emission because the bonding orbital is dominated by an N-orbital component, owing to its lower energy than that of B. The peak energy positions (vertical arrows) and the shoulder structures (vertical lines) of the B K of these materials are different from each other, reflecting different chemical bonding states owing to different crystal structures. By using a high energy resolution, elemental and chemical state analyses and those mappings are possible [5–7,26–30]. The emission due to the process d is also affected by the chemical state of the materials [31,32]. 2.2. Preparation of p/n-Controlled SrB Bulk Specimens The molten-salt method reported for low-temperature synthesis of CaB powders [33] was applied for the present preparation of SrB specimens. The reaction used is as fol- lows: SrCl + 6NaBH ! SrB + 2NaCL +12H + 4Na. Three SrB materials were pre- 2 4 6 2 6 pared by using different starting materials, with compositions of: Sr:B = 1:1 (Sr excess), 1:6 (stoichiometry), and 1:12 (Sr-deficient). Well-mixed starting materials of SrCl and NaBH were placed in crucibles of stainless 2 4 steel, heated up to 1073 K and maintained for 10 h under an Ar atmosphere. The produced materials were washed with acid and water to remove impurities other than SrB . The obtained powder materials were sintered at 1800 K and 50 MPa for 20 min by the pulsed electric current sintering method, and bulk specimens were obtained. The crystallinity of those specimens was examined and confirmed as SrB crystalline specimens by X-ray diffrac- tion. From the measurements of the Seebeck coefficient, the obtained specimens from the starting materials of Sr:B = 1:1 (Sr excess) and 1:6 (stoichiometry) were n-type semi- Appl. Sci. 2021, 11, 9588 4 of 9 conductors. On the other hand, the material started with Sr:B = 1:12 (Sr-deficient) was a p-type semiconductor. Figure 2. (a) SXES-EPMA system used. The SXES spectrometer is composed of gratings and a CCD detector, which enables a parallel detection in a certain energy range. (b) B K-emission spectra of pure boron and boron compounds. Peak energy position (arrows) and shoulder structures (line) are different each other, reflecting different chemical bonding states owing to different crystal structures. 3. Results 3.1. Observation of p/n-Controlled SrB by Backscattering Electron Figure 3 shows backscattered electron (BSE) images of sintered bulk specimens of the n-type, prepared with Sr:B = 1:1 and 1:6, and p-type, prepared with Sr:B = 1:12 (Sr-deficient composition). It was observed that the images of the n-type specimen are dominated by bright and rather homogeneous regions. On the other hand, the BSE image of the p-type specimen in Figure 3c is apparently inhomogeneous; it shows a co-existence of bright and dark regions. The BSE image shows a larger intensity for an area with a larger averaged atomic number Z. Thus, the dark regions in Figure 3c could be understood as apparently Sr-deficient regions of 1 m or much smaller in size. A Sr-deficient, hole-doping, SrB specimen could be a p-type semiconductor. However, the BSE image cannot give us chemical state information. Thus, the following SXES investigation is important to judge the physical properties of these materials. Figure 3. Back-scattering electron images of sintered SrB6 bulk specimens. The image of the p-type specimen is apparently inhomogeneous. Dark contrast regions could be Sr-deficient regions. (a) Sr:B = 1:1_n-type; (b) Sr:B = 1:6_n-type;.(c) Sr:B = 1:12_p-type. 3.2. SXES Mapping of n-Type SrB Figure 4a shows a BSE image of a piece of an n-type SrB specimen prepared with a Sr-excess composition of Sr:B = 1:1. A spectral mapping procedure was performed with a probe current of 40 nA at an accelerating voltage of 5 kV. The specimen area in Figure 4a was divided into 20 15 pixels of about 0.6 m pitch. Electrons of 5 keV, impinged on the SrB surface, spread out inside the material via inelastic scattering of about 0.22 m in diameter, Appl. Sci. 2021, 11, 9588 5 of 9 which was evaluated by using Reed’s equation [34]. The size, which corresponds to the lateral spatial resolution of the SXES measurement, is smaller than the pixel size of 0.6 m. SXES spectra were obtained from each pixel with an acquisition time of 20 s. Figure 4b shows a map of the Sr M -emission intensity of each pixel divided by an averaged value of the Sr M intensity of the area examined. The positions of relatively Sr-deficient areas with blue color in Figure 4b are a little different from those which appear in the dark contrast area in the BSE image in Figure 4a. This could be due to a smaller information depth of the BSE image than that of the X-ray emission (electron probe penetration depth) [35]. The raw spectra of the squared four-pixel areas A and B are shown in Figure 4c, which show a sufficient signal -o-noise ratio. Each spectrum shows B K-emission intensity due to transitions from VB to K-shell (1s), which corresponds to c in Figure 1, and Sr M -emission intensity due to transitions from N -shell (4p) to M -shell (3d), which corresponds to 2,3 4,5 Figure 1d [36,37]. These spectra intensities were normalized by the maximum intensity of B K-emission. Although the area B exhibits a slightly smaller Sr content than that of A in Figure 4b, the intensities of Sr M -emission of those areas in Figure 4c are almost the same, suggesting the inhomogeneity was small. Figure 4. (a) BSI image, (b) Sr M -emission intensity map, (c) spectra of areas A and B in (b), (d) chemical shift map of B K-emission, and (e) B K-emission spectra of A and B in (d). When the amount of Sr in an area is deficient, the amount of the valence charge of the B cluster network of the area should be deficient (hole-doped). This causes a shift in B 1s-level (chemical shift) to a larger binding energy side. This can be observed as a shift in the B K-emission spectrum to the larger energy side as already reported for Na-doped CaB [20] and Ca-deficient n-type CaB [21]. For making a chemical shift map, monitoring 6 6 of the spectrum intensity from 187 to 188 eV at the right-hand side of the spectrum (which corresponds to the top of VB) is useful [20,21]. The map of the intensity of 187–188 eV is shown in Figure 4d, in which the intensity of each pixel is divided by the averaged value of the intensities of all pixels. When the chemical shift to the higher energy side is large, the intensity in Figure 4d is large. It should be noted that larger intensity areas in Figure 4d correspond with smaller Sr-M intensity areas in Figure 4c. The B K-emission spectra of areas A and B are shown in Figure 4e. The gray band of 187–188 eV is the Appl. Sci. 2021, 11, 9588 6 of 9 energy window used for making Figure 4d. Although the Sr M intensity of the areas are almost the same, the peak of the spectrum B shows a shift to the larger energy side of about 0.1 eV and a slightly longer tailing to the higher energy side, which is a small change in intensity distribution. These could be due to a hole-doping caused by a small Sr deficiency as observed in Figure 4b. The area could be a hole-doped p-type region embedded in a n-type bulk specimen. This local inhomogeneity of Sr could be due to an inhomogeneity in the starting materials. 3.3. SXES Mapping of p-Type SrB Figure 5a shows a BSE image of a p-type SrB bulk specimen prepared with an Sr- deficient composition of Sr:B = 1:12. As the contrast of BSI depends on the atomic number, the complex white and black contrast in the BSI image suggests an inhomogeneous distri- bution of Sr. Figure 5b shows an intensity map of Sr M -emission divided by an averaged value. The spectra (raw data) of areas A and B are shown in Figure 5c. The spectrum B shows a largely decreased Sr-M intensity than that of A. Figure 5. (a) BSI image, (b) spectra of areas A and B in (c), (c) Sr-M -emission intensity map, (d) chemical shift map of B K-emission, (e) B K-emission spectra of areas of A and B in (d). Figure 5d is a chemical shift map prepared using the same manner for that in Figure 4d. It is clearly seen that the B K-emission spectra of Sr-deficient regions, dark areas in Figure 5b, show a chemical shift to the larger energy side, as seen in bright color in Figure 5d. The enlarged B K-emission spectra of areas A and B are shown in Figure 5e. The gray band of 187–188 eV is the energy window used to make Figure 5d. The spectrum of the area B with a large Sr-deficient region shows not only a shift of the B K-emission peak position to the larger energy side, but also an additional shoulder structure, indicated by vertical lines. This means that the area could have a crystal structure comprising largely deformed SrB , or a structure different from that of SrB . Such shoulder structures of B K-emission spectra were also observed in Na-doped [20] and Ca-deficient [21] p-type CaB bulk specimens. A different crystal structure of boron can show a different peak energy in B K-emission as already shown in Figure 2b. Thus, the area B could be a p-type region, but the amount of the peak shift cannot be explained by the hole-doping only. On the other hand, the intensity profile of spectrum A in Figure 5e is similar to those in Figure 4e. The Sr-M intensity of the Appl. Sci. 2021, 11, 9588 7 of 9 area A in Figure 5c is smaller than that of the spectrum of area A in Figure 4c. Furthermore, the peak position of the B K-spectrum shifted slightly to the larger energy side about 0.1 eV than that of A in Figure 4e. Thus, area A could be a hole-doped p-type region having the SrB structure. Thus, the area A should be representative of p-type SrB aimed for in the 6 6 specimen preparation. 4. Discussion The present experimental results of SXES mappings showed that the present n-type SrB bulk specimen was almost uniform except for a local fluctuation in Sr content. On the other hand, p-type bulk specimen was apparently not uniform. The specimen was com- posed of two p-type regions. One was the region containing a small amount of Sr -deficiency and having the SrB type crystal structure, which was the material aimed for in specimen preparation. The other was the region with a large amount of Sr deficiency, which had a largely deformed SrB structure or a differently structured boron material. This could be the result of an Sr-deficient composition of starting material used for the molten-salt method. From the experimental results, the fine SrB particles prepared by molten-salt method may have had a large dispersion of Sr content. Therefore, any process to separate the two types of materials, a centrifugal process for example, before the sintering process would be effective to prepare a uniform p-type SrB bulk specimen. 5. Conclusions Homogeneity of composition and the related chemical states of p/n-controlled SrB bulk specimens were examined by using an SXES microscope. It was revealed that the present p-type bulk specimen is composed of two types of regions. Those regions showed differences in the amount of Sr content and the crystal lattice. Based on the results, an additional process was proposed to separate the two materials prepared by the molten- salt method. Therefore, we presented that the nondestructive inspection process of bulk materials using a SXES microscope can realize quick feedback of the results of chemical state analyses of the material to the production process and contribute to an improvement in the specimen preparation process. Author Contributions: Specimen preparation and characterization, M.T. (Masatoshi Takeda); soft X- ray emission experiment, M.T. (Masami Terauchi); SXES data analysis and discussion, M.T. (Masami Terauchi) and Y.K.S.; writing original draft preparation and funding acquisition, M.T. (Masami Terauchi) and M.T. (Masatoshi Takeda). All authors have read and agreed to the published version of the manuscript. Funding: This research was funded by the Research Program of the Dynamic Alliance for Open Innovation Bridging Human, Environment and Materials of the Ministry of Education, Culture, Sports, Science and Technology, Japan, and the Network Joint Research Centre for Materials and Devices; Japan Society for the Promotion of Science KAKENHI (grant numbers 15H02299; 19K21838). Institutional Review Board Statement: Not applicable. Informed Consent Statement: Not applicable. Acknowledgments: The authors thank M. Ageishi of the Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, for his skillful technical assistance. Conflicts of Interest: The authors declare no conflict of interest. References 1. Kimoto, K.; Xie, R.J.; Matsui, Y.; Ishizuka, K.; Hirosaki, N. Direct observation of single dopant atom in light-emitting phosphor of 2+ -SiAlON:Eu . Appl. Phys. Lett. 2009, 94, 041908. [CrossRef] 2. Sato, Y.; Terauchi, M.; Adachi, K. High energy-resolution electron energy-loss spectroscopy study on the near-infrared scattering mechanism of Cs0.33WO3 crystals and nanoparticles. J. Appl. Phys. 2012, 112, 074308. [CrossRef] 3. Krivanek, O.L.; Lovejoy, T.C.; Dellby, N.; Aoki, T.; Carpenter, R.W.; Rez, P.; Soignard, E.; Zhu, J.; Batson, P.E.; Lagos, M.J.; et al. Vibrational spectroscopy in the electron microscope. Nature 2014, 514, 209–212. [CrossRef] [PubMed] Appl. Sci. 2021, 11, 9588 8 of 9 4. Tsuda, K.; Tanaka, M. Direct observation of the symmetry breaking of the nanometer-scale local structure in the paraelectric cubic phase of BaTiO3 using convergent-beam electron diffraction. Appl. Phys. Express 2016, 9, 071501. [CrossRef] 5. Takahashi, H.; Handa, N.; Murano, T.; Terauchi, M.; Koike, M.; Kawachi, T.; Imazono, T.; Hasegawa, N.; Koeda, M.; Nagano, T.; et al. Chemical State Mapping via Soft X-rays using a Wavelength Dispersive Soft X-ray Emission Spectrometer with High Energy Resolution. Microsc. Microanal. 2013, 19 (Suppl. S2), 1258–1259. [CrossRef] 6. Terauchi, M.; Koshiya, S.; Satoh, F.; Takahashi, H.; Handa, N.; Murano, T.; Koike, M.; Imazono, T.; Koeda, M.; Nagano, T.; et al. Chemical state information of bulk specimens obtained by SEM-based soft-x-ray emission spectrometry. Microsc. Microanal. 2014, 20, 692–697. [CrossRef] 7. Takahashi, H.; Murano, T.; Takakura, M.; Asahina, S.; Terauchi, M.; Koike, M.; Imazono, T.; Koeda, M.; Nagano, T. Development of soft X-ray emission spectrometer for EPMA/SEM and its application. IOP Conf. Ser. Mater. Sci. Eng. 2016, 109, 012017. [CrossRef] 8. Gunji, S.; Kaminura, H. First-principle study on metal-doped icosahedral B12 solids. Phys. Rev. B 1996, 54, 13665–13673. [CrossRef] 9. Nagatochi, T.; Hyodo, H.; Sumiyoshi, A.; Soga, K.; Sato, Y.; Terauchi, M.; Esaka, F.; Kimura, K. Superconductivity in Li-doped -rhombohedral boron. Phys. Rev. B 2011, 83, 184507. [CrossRef] 10. Etourneau, J.; Hagenmuller, P. Structure and physical features of the rare-earth borides. Philos. Mag. B 1985, 52, 589–610. [CrossRef] 11. Albert, B.; Hillebrecht, H. Boron: Elementary Challenge for Experimenters and Theoreticians. Angew. Chem. Int. Ed. 2009, 48, 8640–8668. [CrossRef] 12. Nagamatsu, J.; Nakagawa, N.; Muranaka, T.; Zenitani, Y.; Akimitsu, J. Superconductivity at 39 K in magnesium diboride. Nature 2001, 40, 63–64. [CrossRef] [PubMed] 13. Haga, J.; Mizui, N.; Nagamichi, T.; Okamoto, A. Effect of Boron on Mechanical Properties and Recrystallization Behavior of Ti-added Ultra-low Carbon Cold-rolled Steel Sheets. ISIJ Int. 1998, 38, 580–586. [CrossRef] 14. Scheifers, J.P.; Zhang, Y.; Fokwa, B.P.T. Boron: Enabling Exciting Metal-Rich Structures and Magnetic Properties. Acc. Chem. Res. 2017, 50, 2317–2325. [CrossRef] 15. Zhang, X.; Wang, B.; Huang, W.; Chen, Y.; Wang, G.; Zheng, L.; Zhu, W.; Bedzyk, M.J.; Zhang, W.; Medvedeva, J.E.; et al. Synergistic Boron Doping of Semiconductor and Dielectric Layers for High-Performance Metal Oxide Transistors: Interplay of Experiment and Theory. J. Am. Chem. Soc. 2018, 140, 12501–12510. [CrossRef] [PubMed] 16. International Atomic Energy Agency. Current Status of Neutron Capture Therapy; International Atomic Energy Agency: Vienna, Austria, 2001. 17. Takeda, M.; Fukuda, T.; Domingo, F.; Miura, T. Thermoelectric properties of some metal borides. J. Solid State Chem. 2004, 177, 471–475. [CrossRef] 18. Takeda, M.; Terui, N.; Takahashi, N.; Ueda, N. Improvement of thermoelectric properties of alkaline-earth hexaborides. J. Solid State Chem. 2006, 179, 2823–2826. [CrossRef] 19. Kuribayashi, H.; Makino, S.; Takeda, M. Synthesis and Characterization of p-type CaB6. Abstract of ISBB-18. In Proceedings of the 2014 IEEE International Symposium on Bioelectronics and Bioinformatics, Chung Li, Taiwan, 11–14 April 2014; p. 148. 20. Terauchi, M.; Sato, Y. Chemical State Analyses by Soft X-ray Emission Spectroscopy. JEOL NEWS 2018, 53, 30–35. 21. Terauchi, M.; Sato, Y.K.; Takeda, M. Chemical State Mapping of Bulk Materials by Electron Microscopy Based Soft X-ray Emission Spectroscopy. Mater. Jpn. 2021, 60, 341–346. [CrossRef] 22. Terauchi, M.; Yamamoto, H.; Tanaka, M. Development of a sub-eV resolution soft-X-ray spectrometer for a transmission electron microscope. J. Electron Microscopy 2001, 50, 101–104. [CrossRef] 23. Terauchi, M.; Kawana, M. Soft-X-ray emission spectroscopy based on TEM – Toward a total electronic structure analysis. Ultramicroscopy 2006, 106, 1069–1075. [CrossRef] [PubMed] 24. Terauchi, M. Valence Electron Spectroscopy for Transmission Electron Microscopy. In Transmission Electron Microscopy Characteri- zation of Nanomaterials, 1st ed.; Kumar, C.S.S.R., Ed.; Springer: Berlin/Heidelberg, Germany, 2014. [CrossRef] 25. Yin, Z.; Rehanek, J.; Lochel, H.; Braig, C.; Buck, J.; Frisov, A.; Viefhaus, J.; Erko, A.; Techert, S. Highly efficient soft X-ray spectrometer based on a reflection zone platre for resonant inelastic X-ray scattering measurements. Opt. EXPRESS 2017, 25, 10984–10996. [CrossRef] 26. Ishii, S.; Terauchi, M.; Sato, Y.; Tamura, N.; Aono, M.; Abe, H. Soft X-ray emission spectroscopy study of characteristic bonding states and its distribution of amorphous carbon-nitride (a-CNx) films. Microscopy 2018, 67, 244–249. [CrossRef] [PubMed] 27. Terauchi, M.; Takahashi, H.; Takakura, M.; Murano, T.; Koshiya, S. Handbook of Soft X-ray Emission Spectra, 6th ed.; JEOL Ltd.: Tokyo, Japan, 2020; pp. 244–250. 28. Kasada, R.; Ha, Y.; Higuchi, T.; Sakamoto, K. Chemical State Mapping of Degraded B4C Control Rod Investigated with Soft X-ray Emission Spectrometer in Electron Probe Micro-analysis. Sci. Rep. 2016, 6, 25700. [CrossRef] [PubMed] 29. Mukai, K.; Kasada, R.; Yabuuchi, K.; Konishi, S.; Kim, J.H.; Nakamichi, M. Valence Electron and Chemical State Analysis of Be12M (M=Ti, V) Beryllides by Soft X-ray Emission Spectroscopy. ACS Appl. Energy Mater. 2019, 2, 2889–2895. [CrossRef] 30. MacRae, C.M.; Pearce, M.A.; Wilson, N.C.; Torpy, A.; Glenn, M.A.; Russo, S.P. Soft X-ray and Cathodoluminescence Examination of a Tanzanian Graphite Deposit. Microsc. Microanal. 2020, 26, 814–820. [CrossRef] 31. Terauchi, M.; Koshiya, S.; Kimoto, K. Information observed in Ti-L, and Ti-L`, emission lines of Ti and its oxides. IOP Conf. Ser. Mater. Sci. Eng. 2018, 304, 012018. [CrossRef] Appl. Sci. 2021, 11, 9588 9 of 9 32. Terauchi, M. Information of valence charge of 3d transition metal elements observed in L-emission spectra. Microscopy 2019, 68, 330–337. [CrossRef] 33. Shi, L.; Gu, Y.; Chen, L.; Yang, Z.; Ma, J.; Qian, Y. Low Temperature Synthesis and Characterization of Cubic CaB6 Ultrafine powders. Chem. Lett. 2003, 32, 958–959. [CrossRef] 34. Reed, S.J.B. Electron Microprobe Analysis, 2nd ed.; Cambridge University Press: Cambridge, UK, 1993; pp. 199–201. 35. Niedrig, H.; Rau, E.I. Information depth and spatial resolution in BSE microtomography. Nucl. Instr. Meth. Phys. Res. B 1998, 142, 523–534. [CrossRef] 36. Bearden, J.A. X-ray Wavelengths. Rev. Mod. Phys. 1967, 39, 78–124. [CrossRef] 37. Zschornack, G. Handbook of X-ray Data, 1st ed.; Springer: Berlin/Heidelberg, Germany, 2007; p. 265.
Applied Sciences – Multidisciplinary Digital Publishing Institute
Published: Oct 14, 2021
Keywords: soft X-ray emission spectroscopy microscope; chemical shift map; hole-doping; elemental map; spectrum imaging
You can share this free article with as many people as you like with the url below! We hope you enjoy this feature!
Read and print from thousands of top scholarly journals.
Already have an account? Log in
Bookmark this article. You can see your Bookmarks on your DeepDyve Library.
To save an article, log in first, or sign up for a DeepDyve account if you don’t already have one.
Copy and paste the desired citation format or use the link below to download a file formatted for EndNote
Access the full text.
Sign up today, get DeepDyve free for 14 days.
All DeepDyve websites use cookies to improve your online experience. They were placed on your computer when you launched this website. You can change your cookie settings through your browser.