Optimal perturbations and transition energy thresholds in boundary layer shear flows
Optimal perturbations and transition energy thresholds in boundary layer shear flows
Vavaliaris, Chris;Beneitez, Miguel;Henningson, Dan S.
Optimal perturbations and transition energy thresholds in boundary layer shear ﬂows y z Chris Vavaliaris, Miguel Beneitez, and Dan S. Henningson Linné FLOW Centre and Swedish e-Science Research Centre (SeRC), KTH Mechanics, Royal Institute of Technology, SE10044 Stockholm, Sweden (Dated: May 24, 2020) Subcritical transition to turbulence in spatially developing boundary layer ﬂows can be triggered eﬃciently by ﬁnite amplitude perturbations. In this work, we employ adjoint-based optimization to identify optimal initial perturbations in the Blasius boundary layer, culminating in the computation of the subcritical transition critical energy threshold and the associated fully localized critical op- timum in a spatially extended conﬁguration, the so called minimal seed. By dynamically rescaling the variables with the local boundary layer thickness, we show that the identiﬁed edge trajectory approaches the same attracting phase space region as previously reported edge trajectories, and reaches the region more eﬃciently. Shear ﬂow transition to turbulence is a complex classical physics problem demonstrating rich spatiotemporal dy- namics [1–3]. The inherently nonlinear process of subcritical bifurcations and the resulting formation of spatially localized states play a dominant role both in ﬂuid dynamics [4, 5] and in other areas of physics [6, 7]. The study of subcritical transition in shear ﬂows has seen signiﬁcant progress by the application of concepts and methods derived from a dynamical systems viewpoint, which naturally arise from the phase space coexistence of two attracting regimes. Such concepts are the edge manifold, which is the invariant set separating trajectories approaching the laminar and turbulent attractors, and edge states, saddle states present on this manifold [8, 9]. Another important phase space concept is the minimal seed, which is the point on the edge manifold that is closest to the laminar attractor in the L (energy) norm. Perturbing the minimal seed inﬁnitesimally along its unstable direction yields the lowest- energy initial perturbation that can trigger subcritical transition to turbulence. This framework, along with nonlinear optimization techniques [10–12], has been used to ﬁnd nonlinear optima and the minimal seed in spatially homogeneous ﬂows such as pipe ﬂow [13, 14], plane Couette ﬂow [15–17] and the asymptotic suction boundary layer ﬂow . Previous work has shown that the application of dynamical systems concepts can be fruitful in spatially developing ﬂows too [19–24]. The canonical example of spatially developing ﬂows is boundary layers, and speciﬁcally the Blasius boundary layer, which approximates the incompressible high-Reynolds laminar ﬂow over a horizontal semi-inﬁnite ﬂat plate [25, 26]. No ﬁxed length scale exists and the Reynolds number increases along the streamwise direction x; it is usually deﬁned with the boundary layer’s displacement thickness (x) := (1 U (x; y)=U )dy, where U denotes the streamwise velocity ﬁeld, U the freestream velocity, and y the wall-normal direction. The Blasius solution is unstable to perturbations of suﬃciently high amplitude, but becomes linearly unstable too at R ' 520 [27, 28]. Thus, depending on the local Reynolds number, transition can be triggered both subcritically and supercritically. A key diﬀerence between the two transition routes is their characteristic timescales, with the subcritical route being faster . Exploiting this timescale separation, we focus on Blasius transition for low-to-moderate R values, where the subcritical route is dominant. Previous work has attempted to identify optimal initial perturbations for the Blasius boundary layer . Although these authors do indeed ﬁnd nonlinear nonlocalized optima in a narrow domain, they employ a diﬀerent deﬁnition for the minimal seed. More speciﬁcally, they identify a “basic building block”  at the core of the found optima for initial energies above a “nonlinearity threshold” . This, however, is not the optimal initial perturbation at the critical energy threshold for transition, and is thus not consistent with the above deﬁnition. In this work, we identify the critical energy threshold and fully localized minimal seed for subcritical transition in a spatially developing boundary layer ﬂow. Moreover, we investigate the edge manifold’s dynamics right from its point closest to the laminar solution, and demonstrate that trajectories starting from diﬀerent regions of the manifold do indeed approach the same attracting region in phase space. Within the subcritical transition timescales, we use adjoint based optimization to identify optimal initial pertur- bations and the critical energy threshold E for transition. We employ a spatially extended domain, allowing for full localization of the perturbations. We timemarch the Blasius solution until a converged state is reached and use it as the baseﬂow; we consider the evolution of perturbations about this baseﬂow. For the optimization we employ a well established variational framework [10–12]. The optimizing functional is the perturbation kinetic energy gain at time horizon T 2 2 G := E =E = ku (T; x)k = ku (0;x)k ; T T 0 present address: Integrated Applied Math, University of New Hampshire, Durham NH 03824, USA; firstname.lastname@example.org email@example.com firstname.lastname@example.org arXiv:1911.07019v3 [physics.flu-dyn] 15 Dec 2020 2 4.5 no subcr. transition subcr. transition 4.0 bound minimal seed 0.0004 3.5 0.0003 0.0002 3.0 100 200 300 2.5 2.0 1.5 0.034 0.035 0.036 0.037 bound 1.0 4 3.644 × 10 T 3.50 × 10 0.5 3.70 × 10 1.0 1.5 2.0 2.5 3.0 3.5 4.0 0 250 500 750 1000 1250 1500 1750 2000 10 E0 (a) (b) Figure 1. (a) Energy-gain diagram. The points mark the optima found for each E level; red squares trigger subcritical transition, blue circles do not. The critical energy threshold E and minimal seed are given by the green diamond. The shaded area is shown in the inset. (b) Edge tracking results. The green line is the identiﬁed edge trajectory; the blue and red lines correspond to optima below and above E (see legend). The laminar and turbulent vorticity bounds used are given by the horizontal gray dashed lines; their enforcement begins at t = 200. Their values are based on those successfully used in  and are determined in a trial and error process, to ensure that perturbations have suﬃcient time to clearly evolve towards transition or relaminarization, but to also prevent unnecessarily long simulation times. The black dashed lines are some of the trajectories ruled out during the edge tracking. The shaded area is shown in the inset. where u(t; x) denotes the perturbation velocity ﬁeld and kk the L norm. The governing equations are the Navier- Stokes and continuity equations. To update the initial ﬁeld u we employ the gradient-rotation method , which ensures that E remains constant without an explicit energy constraint, while to relax the high memory demand during the adjoint integration we incorporate a memory checkpointing routine. The simulations are done using the spectral element code Nek5000  and speciﬁcally the fully nonlinear adjoint based optimization codebase developed in , which marked the ﬁrst nonlinear optimization done with Nek5000 implementing the gradient rotation and memory checkpointing routines. The use of state-of-the-art methods is critical in such a computationally demanding undertaking: compared to previous studies , we use a 2.5-times longer and 10-times wider domain, as well as a 5-times longer optimization time horizon. Additionally, on average 154 optimization iterations are performed for each reported optimum. Numerical convergence is checked by the residual r := ( L ) =k L k , where L is the n u n u n 0 0 problem’s Lagrangian . The parameters explicitly appearing in the algorithm are the initial energy E , the time horizon T , and the inﬂow Reynolds number R . Due to the spatial variation, the streamwise domain length L implicitly aﬀects the in x optimization as well. For ﬁxed R , the values of T and L control the range of local Reynolds numbers the ﬂow in x evolution will span. Therefore, they determine the dynamical behavior present within the optimization horizon. The streamwise, normal and spanwise directions are denoted by x, y and z, respectively. The presented results are obtained for R = 275, T = 400 and domain dimensions (L ; L ; L ) = (500; 60; 100). An inﬂow fringe region in x y z of length l = 25 is used, with l being part of L . The length and velocity scales used for nondimensionalization x x x are the inﬂow boundary layer displacement thickness (upstream of the fringe) and U ; the used timescale is thus =U . The reported R value is attained right downstream of the fringe. In terms of boundary conditions, at the 1 in inﬂow we set the velocity to its base value (zero perturbation), while a no-slip condition is imposed at the bottom wall. A stress-free (Neumann) condition is imposed at the outﬂow. At the top boundary, the streamwise and spanwise velocities are set to their base values (zero perturbation), and a stress free condition is used for the normal velocity. Periodicity is imposed in the spanwise direction. The derivation of the corresponding boundary conditions for the adjoint equation is presented in full in . The initial perturbation ﬁeld consists of a divergence-free pair of tilted streamwise vortices, so that no symmetries are introduced into the resulting solutions . We do not require transition to be triggered within the time horizon T . To establish whether or not an optimum triggers transition, we perform long-time direct runs with time horizon t = 1500 (L = 2500; L , L as above), f x y z 2 1=2 using the volume-averaged streamwise vorticity ! := (1=V j! j dv) as an observable, where dv = dxdydz and V x x is the domain’s volume. ! (t) characterizes the streamwise vortices’ strength, and is equal to zero for the baseﬂow. 10 G T 3 Z X (a) (b) (c) (d) Figure 2. Streamwise perturbation velocity (blue for negative; red for positive) and vortex criterion (green) contours of the minimal seed’s evolution. Side view in top half, top view in bottom half; ﬂow towards the right. Spatial dimensions between diﬀerent subﬁgures not to scale. The double arrow gives the minimal seed’s streamwise length (22 units). Contour levels for 3 3 2 2 5 (a)-(c) u = 8 10 , 6 10 ; (d) u = 6 10 , 5 10 , = 1 10 . (a) t = 0; the minimal seed is nonsymmetric and backwards leaning. (b) t = 60; the perturbation is leaning forward after the Orr mechanism’s eﬀect. (c) t = 150; the perturbation is getting elongated and consists of high- and low-speed streaks created by the liftup mechanism. (d) t = 2500; the perturbation is considerably longer, while maintaining its streaky structure; the contours help identify its active core , typical of edge trajectory perturbations. Transitioning optima present an ever increasing ! (t) evolution; nontransitioning ones transiently grow and then decay while slowly relaminarizing. To calculate E we follow a bisection process. Starting from two E levels, one leading to subcritical transition E c 0 0;T and one to relaminarization E , we choose their average value, E = 1=2(E +E ), and perform an optimization 0;L 0;i 0;T 0;L for this energy level. If the calculated optimum triggers transition, then E E ; otherwise E E . We 0;T 0;i 0;L 0;i then set E in the same fashion and continue the iterative process . Having approached E with an accuracy of 0;i+1 c O(10 ), we employ an edge tracking algorithm [8, 24, 35] to reﬁne it and ensure that the calculated critical threshold and optimum do indeed lie on the edge manifold. The edge tracking is performed using the in-house collocation code SIMSON . During the edge tracking no perturbation shape optimization takes place; the only parameter changing is E for ﬁxed shape. The resulting E is thus an approximation of the exact value that can only be computed by 0 c resuming the optimization runs on diﬀerent E levels all the way to E (see e.g. ), which is currently intractable 0 c due to the associated computational cost. Fig. 1a presents the optimization results, with each point corresponding to the identiﬁed optimal initial perturbation. Increasing E leads to increased gain, although with diﬀerent increasing rates for energies below and above E . For 0 c E < E the gain increases slowly with E , with the rate getting larger as E is approached. For E > E the gain 0 c 0 c 0 c increases rapidly with E , signifying that a qualitatively diﬀerent range of dynamics is now within reach. Crossing the energy threshold E means that the optima can now access the turbulent dynamics, leading to the attainment of highly energetic endﬂows via a much more eﬀective extraction of energy from the baseﬂow. We identify the critical energy threshold separating the optima undergoing subcritical transition and those that do 2 5 not, converging to the value E = 3:644 10 2 10 . E is obtained by an edge tracking computation, resulting c c in the closest edge-bracketing trajectories presenting a separation of 2% at t = 824:6 . In phase space terms, E characterizes the lowest-energy iso-hypersurface that intersects the edge manifold; the minimal seed is the initial perturbation corresponding to the intersection point. The minimal seed identiﬁed in the present conﬁguration is the point on the edge manifold that is closest to the laminar solution at R (x ) = 425:1, where x corresponds to the m m center of mass of the optimum’s spanwise velocity. Due to the spatial development, E and the minimal seed depend on the local streamwise coordinate x, since x sets the local Reynolds number R (x). Fig. 1b shows the edge tracking results, with the green solid line being the identiﬁed edge trajectory; the vorticity 4 10 W present study 5 10 W Beneitez et al (2019) 2.25 minimal seed present study laminar solution Beneitez et al (2019) 2.00 minimal seed 2.5 1.75 1.50 2.0 12 10 8 4 1.25 1.5 0.00015 0.00025 1.00 1.0 t = 400 0.0011 0.75 0.5 t = 206 0.50 0.0010 0.0 t = 2500 2.0 0.25 1.5 1.5 0.0009 1.0 1.0 0.00 0.5 0.5 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 0.0 0.0 (a) (b) Figure 3. Arrows indicate the time direction. (a) Phase portrait of the dynamically rescaled edge trajectories identiﬁed in the present study (green line in Fig. 1b) and in . 2D projections of the green trajectory are given in gray; the area marked by the dashed rectangle is shown in the inset. (b) 2D projection of the phase portrait onto the ( ) plane; laminar ﬁxed point x y located at the origin. The shaded area is shown in the inset. 2 2 curves for the optima for E = 3:5 10 , 3:7 10 are also shown. Despite their small separation in G , the 0 T optima quickly diverge from one another and from the edge trajectory in their vorticity timeseries. Moreover, their early-time vorticity peaks are reached at diﬀerent times, a result of their diﬀerent asymptotic behavior and spatial positioning. Since for E < E triggering subcritical transition is not possible, the corresponding optimum tries to 0 c delay its inevitable viscous decay to achieve the maximum G possible. To do so, it also positions itself further downstream, where the local R (x) values are higher, leading to more favorable growth conditions. On the other hand, transition can be triggered for E > E , thus the respective optimal perturbation tries to trigger it as early as 0 c possible, to take advantage of the turbulent dynamics and attain a higher G . Due to its higher energy content and its ability to trigger transition, it can also survive relatively lower R (x) values; thus, it positions itself further upstream, leaving the bigger part of the domain for its energy growth and spatial spreading. Because of the spatial variation, the streamwise position the localized optima will assume within the domain is also an output of the optimization process, and is not a priori set by the algorithm. It is worthwhile comparing Fig. 1a to the energy-gain diagram found for plane Couette ﬂow (Fig. 3a in ). First, the gain discontinuity at E found in  does not appear in the present study. This occurs because we do not require transition to be triggered within the optimization time horizon, so no turbulent endﬂow needs to be attained. Thus, optima on either side of the edge manifold do not diverge considerably from it, and hence are not so strongly separated in terms of gain at t = T . Second, G keeps increasing for E > E . In , the ﬁnal energy E saturates T 0 c T for E E , leading to the decrease of gain for higher E . On the contrary, in our case E does not saturate, 0 c 0 T because no turbulent domain-ﬁlling endﬂow is attained; the higher the E , the higher the resulting E . The gain 0 T keeps increasing for E & E because E grows “more quickly” than E as the latter is increased. 0 c T 0 The minimal seed is fully localized and consists of alternating areas of positive and negative streamwise velocity tilted against the shear (Fig. 2a). Additionally, it is not spanwise symmetric, which is the only symmetric direction of the underlying baseﬂow, due to the nonsymmetric perturbation used to initiate the optimization algorithm. If the introduced initial perturbation is also spanwise symmetric, then the spanwise symmetry cannot be broken and the simulation is conﬁned to a spanwise symmetric subset of solutions, which is the case in . Due to the baseﬂow’s spanwise symmetry, the spanwise mirrored minimal seed satisﬁes all boundary conditions, and is expected to be an equivalent solution to the same optimization problem. Investigating the minimal seed’s evolution, we identify the occurrence of the Orr  and liftup  energy growth mechanisms. The Orr is a linear mechanism responsible for the early energy growth experienced by the perturbation, t 2 [0; 60], and can be characterized by the tilting of the structure about the spanwise axis. Fig. 2a-b demonstrate that, although initially leaning backwards, the perturbation has been rotated and is leaning forward at t = 60. The Orr is followed by the liftup mechanism, which acts via streamwise vortices displacing areas of high and low streamwise- momentum ﬂuid in the wall-normal direction. This creates distinct areas of low- and high-speed ﬂuid, leading to the formation of streaks (spanwise variation of streamwise velocity) and overall elongation of the advected structure t = 3520 10 y 5 ; the high- and low-speed streaks making up the perturbation can be observed in Fig. 2c-d. Both the tilting of the perturbation caused by the Orr mechanism for t 2 [0; 60] and the elongation caused by the liftup mechanism for t 2 [70; 200] can be seen in the short-time simulation movies available in the supplement . The occurrence of the Orr and liftup mechanisms during the early energy growth stages of optima has also been reported in the past for plane Couette , asymptotic suction boundary layer , and Blasius boundary layer [21, 22] ﬂows. For longer times, we observe an approximately self-similar evolution, with the perturbation maintaining its streaky structure while growing considerably in size due to the boundary layer’s spatial growth, and resembling the edge trajectory identiﬁed in  (Fig. 2d). To investigate the edge manifold’s phase space dynamics we use the volume-averaged streamwise vorticity ! , normal R R 2 1=2 2 1=2 vorticity ! := (1=V j! j dv) , and spanwise velocity w := (1=V jwj dv) . ! is a measure of the streaks’ y y y amplitude, while w measures the lateral activity of the perturbation; all three quantities are zero for the laminar baseﬂow. In order to account for the boundary layer’s spatial growth, we dynamically rescale the independent variables 1=2 with the local displacement thickness (x) and use the rescaled phase variables (i = x; y) := ( = (x)) ! , i i 3=2 W := ( = (x)) w [23, 24]. To get the local values (x(t)) for the optimum’s evolution, we calculate its spanwise velocity’s center of mass x (t), and derive an 11-order least squares polynomial ﬁtting . Using the ﬁtted polynomial p (t), we calculate the values (p (t)) ' (x (t)). m m m The rescaled edge trajectory is shown in Fig. 3, along with part of the edge trajectory found in  using a nonoptimized initial perturbation. Both trajectories approach the same relative attractor in phase space, despite their diﬀerent initial conditions and early-time behavior. It has been shown in  that the corresponding edge trajectory stays in the identiﬁed attracting region for times up to t ' 8000. Moreover, both trajectories form similar loops in the same phase space region and mirror one another in the last part of their dynamics. These results indicate that memory of the trajectories’ initial conditions has indeed been lost . The formation of loops was also identiﬁed in [23, 24], and stems from a self-sustained physical process alternating between the generation of vorticity and the creation of low-speed streaks . The stages of this process can also be identiﬁed by the phases of acceleration and deceleration the advected perturbation goes through, captured in the long-time simulation movie available online. The timestamps provided in Fig. 3a show that the minimal seed needs about half the time to reach the attracting region, compared to the nonoptimized initial perturbation; it also requires an approximately 1700-times lower initial energy level, demonstrating its eﬀectiveness in accessing the edge manifold’s dynamics. To summarize, we have used adjoint based optimization together with edge tracking to calculate optimal initial perturbations for subcritical transition in a spatially developing boundary layer ﬂow, and have estimated the critical 2 5 energy threshold E = 3:644 10 2 10 corresponding to the minimal seed at R (x ) = 425:1. We have observed c m the main mechanisms driving the minimal seed’s early energy growth, and explained the diﬀerences in the positioning between localized optima found above and below E in terms of the optimization process. Finally, by dynamically rescaling the variables, we have shown that two very diﬀerent initial conditions on the edge manifold approach the same attracting phase space region already identiﬁed for longer times . The minimal seed reaches this region more eﬃciently than nonoptimized initial conditions in terms of both initial energy and time needed. Future work includes computing E for additional local Reynolds numbers R (x) to reveal the scaling relationship of the two, as has already been done for parallel ﬂow conﬁgurations [17, 18]. ACKNOWLEDGMENTS We thank Yohann Duguet for helpful discussions, and Enrico Rinaldi, Jacopo Canton and Philipp Schlatter for developing the used numerical codebase. Financial support by the Swedish Research Council (VR) grant no. 2016- 03541 and computing time provided by the Swedish National Infrastructure for Computing (SNIC) are gratefully acknowledged. The open source projects NumPy, SciPy, Matplotlib, FFmpeg and ParaView have been used for this work.  K. Avila, D. Moxey, A. de Lozar, M. Avila, D. Barkley, and B. Hof, The onset of turbulence in pipe ﬂow, Science 333, 192 (2011).  G. Lemoult, L. Shi, K. Avila, S. V. Jalikop, M. Avila, and B. Hof, Directed percolation phase transition to sustained turbulence in Couette ﬂow, Nature Phys 12, 254 (2016).  T. Kreilos, T. Khapko, P. Schlatter, Y. Duguet, D. S. Henningson, and B. Eckhardt, Bypass transition and spot nucleation in boundary layers, Phys. Rev. Fluids 1, 043602 (2016), arXiv:1604.07235 [physics.ﬂu-dyn]. 6  T. M. Schneider, J. F. Gibson, and J. Burke, Snakes and Ladders: Localized Solutions of Plane Couette Flow, Phys. Rev. Lett. 104, 104501 (2010).  B. Eckhardt, Transition to turbulence in shear ﬂows, Physica A 504, 121 (2018).  E. Knobloch, Spatially localized structures in dissipative systems: Open problems, Nonlinearity 21, T45 (2008).  E. Knobloch, Spatial localization in dissipative systems, Annu. Rev. Condens. Matter Phys. 6, 325 (2015).  J. D. Skufca, J. A. Yorke, and B. Eckhardt, Edge of Chaos in a Parallel Shear Flow, Phys. Rev. Lett. 96, 174101 (2006).  T. M. Schneider, B. Eckhardt, and J. A. Yorke, Turbulence Transition and the Edge of Chaos in Pipe Flow, Phys. Rev. Lett. 99, 034502 (2007).  D. P. G. Foures, C. P. Caulﬁeld, and P. J. Schmid, Variational framework for ﬂow optimization using seminorm constraints, Phys. Rev. E 86, 026306 (2012).  R. R. Kerswell, C. C. T. Pringle, and A. P. Willis, An optimization approach for analysing nonlinear stability with transition to turbulence in ﬂuids as an exemplar, Rep. Prog. Phys. 77, 085901 (2014).  R. R. Kerswell, Nonlinear nonmodal stability theory, Annu. Rev. Fluid Mech. 50, 319 (2018).  C. C. T. Pringle and R. R. Kerswell, Using Nonlinear Transient Growth to Construct the Minimal Seed for Shear Flow Turbulence, Phys. Rev. Lett. 105, 154502 (2010).  C. C. T. Pringle, A. P. Willis, and R. R. Kerswell, Minimal seeds for shear ﬂow turbulence: using nonlinear transient growth to touch the edge of chaos, J. Fluid Mech. 702, 415 (2012).  A. Monokrousos, A. Bottaro, L. Brandt, A. Di Vita, and D. S. Henningson, Nonequilibrium Thermodynamics and the Optimal Path to Turbulence in Shear Flows, Phys. Rev. Lett. 106, 134502 (2011).  S. M. E. Rabin, C. P. Caulﬁeld, and R. R. Kerswell, Triggering turbulence eﬃciently in plane Couette ﬂow, J. Fluid Mech. 712, 244 (2012).  Y. Duguet, A. Monokrousos, L. Brandt, and D. S. Henningson, Minimal transition thresholds in plane Couette ﬂow, Phys. Fluids 25, 084103 (2013).  S. Cherubini, P. De Palma, and J.-C. Robinet, Nonlinear optimals in the asymptotic suction boundary layer: Transition thresholds and symmetry breaking, Phys. Fluids 27, 034108 (2015).  S. Cherubini, P. De Palma, J.-C. Robinet, and A. Bottaro, Rapid path to transition via nonlinear localized optimal perturbations in a boundary-layer ﬂow, Phys. Rev. E 82, 066302 (2010).  S. Cherubini, P. De Palma, J.-C. Robinet, and A. Bottaro, Edge states in a boundary layer, Phys. Fluids 23, 051705 (2011).  S. Cherubini, P. De Palma, J.-C. Robinet, and A. Bottaro, The minimal seed of turbulent transition in the boundary layer, J. Fluid Mech. 689, 221 (2011).  S. Cherubini, P. De Palma, J.-C. Robinet, and A. Bottaro, A purely nonlinear route to transition approaching the edge of chaos in a boundary layer, Fluid Dyn. Res. 44, 031404 (2012).  Y. Duguet, P. Schlatter, D. S. Henningson, and B. Eckhardt, Self-Sustained Localized Structures in a Boundary-Layer Flow, Phys. Rev. Lett. 108, 044501 (2012).  M. Beneitez, Y. Duguet, P. Schlatter, and D. S. Henningson, Edge tracking in spatially developing boundary layer ﬂows, J. Fluid Mech. 881, 164 (2019), arXiv:1908.11784 [physics.ﬂu-dyn].  P. J. Schmid and D. S. Henningson, Stability and Transition in Shear Flows, Applied Mathematical Sciences, Vol. 142 (Springer, 2001).  H. Schlichting and K. Gersten, Boundary-Layer Theory, 9th ed. (Springer, 2017).  R. Jordinson, The ﬂat plate boundary layer. Part 1. Numerical integration of the Orr–Sommerfeld equation, J. Fluid Mech. 43, 801 (1970).  S. Berlin, Oblique waves in boundary layer transition, PhD Thesis, KTH Royal Institute of Technology (1998).  D. P. G. Foures, C. P. Caulﬁeld, and P. J. Schmid, Localization of ﬂow structures using 1-norm optimization, J. Fluid Mech. 729, 672 (2013).  P. F. Fischer, J. W. Lottes, and S. G. Kerkemeier, Nek5000 webpage (2008).  E. Rinaldi, J. Canton, and P. Schlatter, The vanishing of strong turbulent fronts in bent pipes, J. Fluid Mech. 866, 487 (2019), arXiv:1902.02294 [physics.ﬂu-dyn].  M. Brynjell-Rahkola, Studies on instability and optimal forcing of incompressible ﬂows, PhD Thesis, KTH Royal Institute of Technology (2017).  D. S. Henningson, A. Lundbladh, and A. V. Johansson, A mechanism for bypass transition from localized disturbances in wall-bounded shear ﬂows, J. Fluid Mech. 250, 169 (1993).  This implicitly assumes that the found optimum completely characterizes its energy level E , meaning that the global optimum is found. Due to nonconvexity this is not guaranteed, so various computational measures have been taken to test whether this is true, and to probe the robustness of the reported results: on each level E , (1) we have reinitialized the algorithm with suboptimal solutions, as well as with optimal and suboptimal solutions of diﬀerent energy levels after rescaling them; (2) we have forced the algorithm to consider suboptimal directions, to see whether the same optimum is eventually recovered. None of these measures led to solutions with higher gains than the ones reported here.  T. Itano and S. Toh, The dynamics of bursting process in wall turbulence, J. Phys. Soc. Jpn. 70, 703 (2001).  M. Chevalier, P. Schlatter, A. Lundbladh, and D. S. Henningson, SIMSON: a pseudo-spectral solver for incompressible boundary layer ﬂows, Technical Report TRITA-MEK 2007:07 (KTH Royal Institute of Technology, 2007).  The E error bounds (2 10 ) are governed by the edge tracking domain’s streamwise length L , due to the spatially c x developing nature of the ﬂow.  W. M. Orr, The stability or instability of the steady motions of a perfect liquid and of a viscous liquid. Part II: A viscous 7 liquid, Proc. R. Irish Acad. A 2, 69 (1907).  M. T. Landahl, A note on an algebraic instability of inviscid parallel shear ﬂows, J. Fluid Mech. 98, 243 (1980).  M. Matsubara and P. H. Alfredsson, Disturbance growth in boundary layers subjected to free-stream turbulence, J. Fluid Mech. 430, 149 (2001).  See supplemental material available online for two short time movies (xy and xz planes), t 2 [0; 200], and one long time movie (xz plane), t 2 [450; 2500], created using the minimal seed’s simulation results. The contour levels in the short time movies are as in Fig. 2a-c; for the long time one, velocity is as in Fig. 2d and = 2:5 10 . In all three movies the camera is moving with constant speed, allowing one to observe the changes in advection speed experienced by the perturbation.  We compute x (t) every 1 time unit for t 2 [0; 850], and every 5 time units for t 2 [855; 2500].
http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.pngPhysicsarXiv (Cornell University)http://www.deepdyve.com/lp/arxiv-cornell-university/optimal-perturbations-and-transition-energy-thresholds-in-boundary-OwPBWD2PMo
Optimal perturbations and transition energy thresholds in boundary layer shear flows